Introduction; Device Description; Scope Of Delivery; Intended Use - Scheppach MTP900 Original Bedienungsanleitung

1. Introduction

Manufaturer:
scheppach Fabrikation von
Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear customer,
We hope your new tool brings you much enjoyment
and success.
Note:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specifi ed,
We recommend:
Read through the complete text in the operating
instructions before installing and commissioning the
device. The operating instructions are intended to
help the user to become familiar with the machine
and take advantage of its application possibilities
in accordance with the recommendations. The
operating instructions contain important information
on how to operate the machine safely, profession-
ally and economically, how to avoid danger, costly
repairs, reduce downtimes and how to increase reli-
ability and service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in
your country.
Keep the operating instructions package with the
machine at all times and store it in a plastic cover to
protect it from dirt and moisture. Read the instruc-
tion manual each time before operating the machine
and carefully follow its information. The machine can
only be operated by persons who were instructed
concerning the operation of the machine and who
are informed about the associated dangers. The
minimum age requirement must be complied with.
20 І 40
2. Device description (Fig. 1-2)
1. Engine Stop Switch
2. Throttle lever
3. Tool Kit
4. Tine Clutch Control
5. Handlebar
6. Knurled screw handlebar stem clamp
7. Shipt Lever
8. Depth regulator rod
9. Transport device
10. Wheel
11. Side Disc
12. Tilling Tines
13. Tine shield extension
14. Chassis with engine and gearbox
3. Scope of delivery (Fig. 2)
• Handlebar (5) (1x)
• Chassis with engine and gearbox (14) (1x)
• Tine shield extension (13) (2x)
• Wheel (10) (2x)
• Tilling Tine (12) (6x)
• Side Disc (11) (2x)
• Tool Kit (3) (1x)
• Transport device (9) (1x)
• Depth regulator rod (8) (1x)
• Original operating instructions (A) (1x)
• Packet with mounting material (B) (1x)
• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for trans-
port damage. When complaints the dealer must be
informed immediately. Subsequent complaints will
not be accepted.
• If possible, store the packaging until the warranty
period has expired.
• Read the operating instructions to make yourself
familiar with the device prior to using it.
• Only use original parts for accessories as well as
for wearing and spare parts. Spare parts are avail-
able from your specialized dealer.
• Specify our part numbers as well as the type and
year of construction of the device in your orders.
m ATTENTION!
The device and packaging materials are not
toys! Children must not be allowed to play with
plastic bags, fi lm and small parts! There is a risk
of swallowing and suffocation!

4. Intended use

The machine is designed for digging over beds and
fi elds. Be sure to observe the restrictions in the ad-
ditional safety instructions.
The equipment is allowed to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse. The user/operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind resulting from such misuse.
D E / A T / C H M F D E / A T / C H