Operation; 5�1 Matching The Input Signal; Phantom Power; Digital Inputs - IMG STAGE LINE DMIX-20 Bedienungsanleitung

5 Operation

Switch on the mixer with the POWER switch (32)� The settings of the
most recent operation will be loaded� Then the mixer will be ready to
use and the screen (9) will display the view that has been selected in
the system settings ( ☞
The steps described in the following merely serve as an aid; other
procedures are possible�
5.1 Matching the input signal
To prevent the input channels from being overloaded and to achieve a
perfect signal-to-noise ratio, first match the input gain of all used chan-
nels to the input signal� If a microphone connected or another signal
source requires phantom power supply, please refer to chapter 5�1�1�
1) Press one of the keys for the input channels (8) to select the chan-
nel� The key will light up�
There is no key to directly select the stereo input channel USB for
digital audio signals from a computer� To select this channel: First
use the key MIXER (22) to go to the screen view "Mixer" (fig� 20)
or "Long Faders" (fig� 21) and then select the channel with the
keys ,  ,  , (18) or by tapping the corresponding control on
the screen�
2) To switch off the indication for the Solo function: When the key
SOLO METER (5) is illuminated, press the key so that it extinguishes�
The level indicators (3) will now apply to the signal at the selected
input�
3) For perfect level control, use the control GAIN (1) of the channel
selected to adjust the gain in such a way that the level on the
indicator is approx� 0 dB� The CLIP LEDs must never light up for
signal peaks; the signal will be distorted when the input channel
is overloaded�
The stereo input channels (CH 17/18, CH 19/ 20 and USB) do not
have any GAIN control; therefore, the input signal for these chan-
nels must be matched via the output level of the signal source�
[The two controls (2) are used to directly adjust the channel volume
of the channels CH 17/18 and CH 19/20 respectively�]
The LED indicator CLIP/ SIG next to the GAIN controls is an additional
aid for checking the input signal: It will light up in green when
a signal is available, and it will light up in red when the input is
overloaded�

5.1.1 Phantom power

For microphones and other signal sources that require phantom power
supply, a separate 48 V phantom power can be activated for each
XLR connection of the input jacks MIC / LINE (27)�
CAUTION Phantom power may damage signal sources with un-
balanced signal outputs� Never apply phantom power
to any inputs to which units with unbalanced output
are connected via XLR plugs�
When the phantom power is switched on or off or when a micro-
phone is connected with the phantom power switched on, signal
peaks occur that, when amplified and sent to the outputs, may
damage the speakers or your hearing� Therefore, first mute the cor-
responding channel with the key MUTE (23) (
use the controls HP1, HP2 and CTRL ROOM (15) to turn back the
volume for the headphones and the control room to the left stop�
1) Press the key 48 V (22)� The screen view for phantom power supply
(fig� 4) will be displayed� The input channels for which phantom
power has been activated will be indicated by a red button with
the lettering ON�
2) To switch the phantom power on or off, tap the button of the
desired input channel on the screen�
28
chapter 6�2�2)�
☞
chapter 5�3�5) and
3) When the phantom power is switched on, a confirmation prompt
will be displayed: Tap "Yes" or press the key ENTER (20) to confirm�
4) To exit this screen view, select a different view�
Assign Gate PEQ
Channel Comp GEQ
DC48V
CH01 CH02 CH03
OFF OFF OFF
CH09 CH10 CH11
OFF OFF OFF
Fig. 4 Phantom power supply

5.1.2 Digital inputs

When the extension module for digital inputs and digital outputs is
☞
installed ( chapter 4�4), an additional digital input signal will be
available for each input channel�
1) Use the key DIGITAL (22) to call up the screen view "Digital Input"
(fig� 5) (press the key twice, if required)�
2) Tap the appropriate area of the screen view to switch the digital
signal for the respective input channel ON or OFF�
3) When a channel has been selected (area highlighted in blue), use
the rotary knob PARAMETER ADJUST (18) to adjust the gain for
the digital signal�
When no extension module is installed, "Please insert the optional
digital card!" will be displayed�
Assign Gate PEQ
Channel Comp GEQ
Plesae insert the optional digital card !
0.0dB 0.0dB 0.0dB 0.0dB
CH01 CH02 CH03 CH04
OFF ON OFF OFF OFF
0.0dB 0.0dB 0.0dB 0.0dB
CH09 CH10 CH11 CH12
OFF ON OFF ON OFF OFF
Fig. 5 Digital input

5.1.3 Signal inversion

The polarity of the signal can be inverted, if required� This is useful
when, for example, an audio source is picked up with two microphones
facing opposite directions (e� g� a drum whose sound is picked up from
above and below)� In this case, one of the two microphone signals
should be inverted to avoid phase cancellation while the two signals
are being mixed�
1) Use the key ASSIGN (22) to call up the screen view "Channel"
(fig� 16) (press the key twice, if required)� The following button
will be shown in the upper left:
Polarity
INV.
Fig. 6
Alternatively, use the button "INV�" in the screen view "Assign"
(fig� 9)�
2) To invert the signal, tap the button; it will appear in colour� To
deactivate the inversion, tap the button again�
FX 1 System Mixer Long
FX 2 Routing DCA Faders
CH04 CH05 CH06 CH07
OFF ON OFF OFF
CH12 CH13 CH14 CH15
OFF OFF OFF OFF
FX 1 System Mixer Long
FX 2 Routing DCA Faders
0.0dB 0.0dB 0.0dB 0.0dB
CH05 CH06 CH07 CH08
OFF OFF OFF OFF
0.0dB 0.0dB 0.0dB 0.0dB
CH13 CH14 CH15 CH16
OFF OFF OFF OFF
Digital Input
Digital Output
CH08
OFF
CH16
OFF
Parameter
CH01
0.0dB