Luxibel LX301 Bedienungsanleitung Seite 5

6.2 DMX512 Con D
Connect the provided XL
the male 3-pin XLR inpu
cable sho ould be a two-co
6.3 DMX512 Cha D
6.4 DMX Start Ad D
All DMX-c controlled devic
This start t address is the
Enter the e correct numbe
You can u use the same st
device.
When all devices have th
particula r channel. In ot
simultane eously. If you s
Changing g the settings of
In the ca se of the 4-cha
second L LX301 to 5 (1 +
6.5 D DMX Control
The DMX X control modes
1-Chann nel Mode
The 1-ch annel mode allo
the 1-cha annel DMX mod
1
↓
ON
3-Chann nel Mode
The 3-ch annel mode allo
advanced d control. Select
1
↓
ON
4-Chann nel Mode
The 4-ch annel mode allo
advanced d control and of
mode by setting DIP swi
1
↓
ON
V. 01 – 0 08/06/2012
nnection
LR cable to the f female 3-pin XL
t of the LX301 . Multiple LX30
ore screened ca able with XLR in
in with Term mination
A DMX termi inator is recomm
to run a long g distance or is
The terminat tor prevents cor
noise. The D DMX terminator
pins 2 and 3 , which is then
device in the e chain.
Please see il lustration.
ddress
ces need a digita al start address
channel numbe er from which th
er and read it fro om the display
tarting address for a whole gro
he same addres ss, all the LX30
ther words: cha nging the settin
et different add resses, each de
f one channel w will only affect th
nnel LX301, yo ou will have to s
+ 4), the third to o 9 (5 + 4) and
Modes
are selected th rough DIP switc
ows you to use the whole flash
e by setting DIP P switch 5 to ON
2 3 4
1-channel mode 1
ows you to cont trol the flash int
t the 3-channel DMX mode by s
2 3 4
3 3-channel mode
ows you to cont trol the flash int
th
ffers a 4 chann nel special pre-p
itch 4 to ON.
2 3 4
4-channel mode 4
LX30 01
LR output of you ur controller and
01s can be linke d through seria
put and output connectors.
mended for inst allations where
in an electrically y noisy environ
rruption of the d digital control si
is simply an XLR R plug with a 12
plugged into th e XLR output so
so that the cor rrect device resp
he device starts s to "listen" to th
located on the b base of the LX3
oup of devices o r enter an indiv
1s will "listen" t to the control si
ngs of one chann nel will affect al
evice will "listen " to a separate
he device in que estion.
set the start add dress of the first
so on.
ches 1 to 5.
range (0 ~ ma x.) and the blin
N.
5 6
tensity, flash du ration and flash
setting DIP swit tches 1 ~ 5 to O
5 6
tensity, flash du ration and flash
programmed eff fects. Select the
5 6
5
d the other side e to
l linking. The lin nking
the DMX cable has
ment (e.g. disco os).
ignal by electric cal
20Ω resistor bet tween
ocket of the last t
ponds to the sig gnals.
he DMX controll ler.
301.
vidual one for ev very
ignal on one
l devices
channel numbe er.
t LX301 to 1, t he
der effect. Sele ect
h rate for more
OFF.
h rate for more
e 4-channel DMX X
©Vellem man nv