Overhead Rigging - JB Systems Light Calypso Bedienungsanleitung

ENGLISH

OVERHEAD RIGGING

 Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.
 Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
 Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The
fixture must be fixed at least 50cm from surrounding walls.
 The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
 Before rigging make sure that the installation area can hold a minimum point load of 10times the device's
weight.
 Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
 The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
 Don't cover any ventilation openings as this may result in overheating.
 The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
DESCRIPTION:
1. Mains input with IEC socket and integrated fuse holder, connect the supplied mains cable here.
2. DMX input
3. DMX output
4. ¼" Jack input for the optional CA-8 hand controller
5. Internal microphone
6. Hanging bracket with 2 knobs on both sides to fasten the unit and a mounting hole to fix a mounting
hook.
7. Slave LED: is lit when the unit is in slave mode
8. Sound LED: blinks to the rhythm of the music while the unit is in audio mode
9. DMX LED: is lit when the unit receives a DMX-signal
10. Master LED: is lit when the unit is switched as master
JB SYSTEMS
®
OPERATION MANUAL
3/52 CALYPSO
ENGLISH
11. MENU button: used to select the different menu items
12. DOWN button: to go back in the menu and to lower the values shown on the display.
13. UP button: to go up in the menu and to increase the values shown on the display.
14. ENTER button: used to confirm your choice.
15. DISPLAY shows the various menus and the selected functions.
HOW TO SETUP:
MAIN MENU:
 To select any of the menu options, press the MENU button up to when the required one is shown on the
display.
 Select the function with the ENTER button. The display will blink.
 Use DOWN and UP button to choose the desired menu option.
 Once the required menu option is selected, press the ENTER button to select. To go back to the functions
without any change press the MENU button or just wait 8 seconds. The menu structure is shown below.
DMX512 Address Setting
Used to set the starting address in a DMX setup.
 Press the MENU button until
is shown on
the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to change the DMX512
address.
 Once the correct address shows on the display,
press the ENTER button to save it.
(or automatically return to the main functions
without any change after 8 seconds)
To go back to the functions without any change press
the MENU button again.
Channel Mode
 Press the MENU button until is shown on
the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select the
1ch
Channel ) or (1 Channel) mode.
 Once the mode is selected, press the ENTER
button to setup
(or automatically return to the main functions
without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Working Mode
Used to set the unit in master or slave mode.
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the current working mode starts blinking in the display
 Use the DOWN and UP buttons to select
(2 light show – slave in anti-sync with the master).
 Once the mode is selected, press the ENTER button save it. (or automatically return to the main functions
without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Remarks: when "SL 1" or "SL 2" is selected, some menu options are not available. When only one unit is
used, you should always select master mode.
JB SYSTEMS
®
OPERATION MANUAL
(4
(master), (slave in sync with the master) or
4/52 CALYPSO