Routine Cleaning; Servicing Instructions - Nilfisk-Advance SD 43-165 Bedienungsanleitung

Routine cleaning

For routine cleaning, your machine is equipped with the
following accessories:
- Spraymaster, drive plate for pads, yellow-and-
brown or green pad for Low-Speed or Spraymaster,
drive plate for pads, red pad for High Speed
Fill the spray can with the desired product.
Fit the drive plate with the desired pad.
Start the machine.
When you pull the Spraymaster lever a few times the
cleaning agent is sprayed onto the floor. Now start
cleaning immediately until a shine is produced.
We advise cleaning the surface in relatively small areas
at a time. The machine is ideal for cleaning with
polymer dispersions. The coatingʼs resistance to
foot traffic and general wear and tear is preserved.
Streaks and marks are easier to remove.
Polishing
For polishing, equip your machine with the following
accessories:
- Drive plate for pads, white pad.
Fit the drive plate with the pad.
Then start the machine.
Service
For repairs, please contact your specialist wholesaler or
one of the service shops.
You will be expertly and quickly served.
Warning! This machine is only intended for use on
level surfaces with a maximum gradient of up to 2 %.
Warning! This machine is not approved for use on
public paths and roads.
Technical specifications
A.C. motor
Rated power
Brush (rpm)
Brush (mm)
Working height (mm)
Working weight (kg)
Protection class
Belt-driven
Handle vibration level m/s2
SD 43-165 SD 43-400 SDM 43-180
230/50 230/50 230/50
1000 1100 1200
5,6 5,7 5,2
165 400 180
430 430 430
250 250 330
30 31 36
I/IPx4 I/IPx0 I/IPx4
X X X
1,05 1,05 1,05

Servicing instructions

the following instructions must always be
observed
When cleaning and servicing the machine, replacing
parts or when changing over to a different function,
switch off the drive and remove the plug.
The power supply lead must not be damaged by driving
over it, crushing, tugging etc.
Check the power supply lead regularly for signs of
damage.
The machine must not be used if the power supply lead
is not in perfect condition.
When using or replacing the power supply or
equipment supply leads, use only those specified by
the manufacturer.
When replacing the plug-and-socket connectors of
power supply or equipment supply leads, splash
protection and mechanical strength must be
assured.
When transporting the machine in lifts, put the shaft/
bar in a vertical position so that it cannot catch on
the lift walls.
The shaft/bar is automatically secured against recoil by
the patented shaft/bar adjustment unit.
Only the spray and cleaning agents suitable for the
machineʼs purpose may be used.
Never use highly flammable, combustible, toxic, health-
hazardous, corrosive or irritant substances.
Repairs, including the fitting of spray agent lines
and hoses, may only be carried out by approved
customer service shops or by specialists in this
field who are familiar with all the relevant safety
regulations.
Storage
When the machine is not being used, store it in a dry
place and in normal room conditions (not below under
0°C).
SDM 43-450 SDM 43-DUO
230/50 230/50
1500 1200-1500
6,5 5,2/8,1
450 190/380
430 430
330 330
40 40
I/IPx0 I/IPx4
X X
1,05 1,05
SDM 43-900/1500 SDM 53-1500
230/50 230/50
1800 1800
7,2 7,2
900/1500 1500
430 530
130/320 130/320
44 46
I/IPx0 I/IPx0
X X
1,05 1,05
9