Proper Use; Technical Data; Before Using The Equipment - EINHELL BT-BD 701 Originalbetriebsanleitung

3. Proper use

This pillar drill is designed for drilling metal, plas-
tic, wood and similar materials. It is intended for
use in the private sector only.
Food and harmful materials may not be pro-
cessed with the machine. The drill chuck is only
designed for use with drill bits and tools with a
shaft diameter of 3 to 16 mm, and for cylindrical
tool shanks. Tools with a tapered shank can also
be used. The machine is intended for use by
adults only.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.

4. Technical data

Nominal input voltage ................... 230V ~ 50 Hz
Nominal power level ................................. 630 W
Operating mode ................................. S2 15 min.
Motor speed ....................................... 1400 min
Output speed ............................ 220 - 2450 min
Speed levels .................................................. 12
Drill chuck mount ........................................ B 16
Gear rim chuck . ............................... Ø 3 - 16 mm
Max. shaft diameter . ................................. 16 mm
Throat ............. ........................................ 126 mm
Dimensions of drill table ... ............ 200 x 195 mm
Angle adjustment of table .. .............. 45° / 0° / 45°
Drill depth ........................... ...................... 60 mm
Pillar diameter ........ .................................. 60 mm
Height ....................................... approx. 850 mm
Base area ..................................... 350 x 230 mm
Weight ... ...................................... approx. 32.5 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
Anl_BT_BD_701_SPK1.indb 20 Anl_BT_BD_701_SPK1.indb 20
GB
L sound pressure level ........................ 62 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level .......................... 75 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
-1
rations if the equipment is used over a pro-
-1
longed period or is not properly guided and
maintained.

5. Before using the equipment

5.1. Assembling the machine (Fig. 1/3/4/5)
•
Place the base plate (1) in the desired posi-
tion.
•
Fasten the pillar (2) with flange using the sup-
plied screws (3).
•
Insert the screw gear in the drill table support.
•
Then insert the gear rack (30) in the drill table
support (5) with the teeth facing the screw
gear (identical projection).
•
Now slip these parts together over the pillar
(2). In doing so, make sure that the gear rack
is correctly seated in the teeth of the screw
gear.
•
To secure the gear rack at the top end, slip
on the guide sleeve (29) over the pillar and
- 20 -
22.11.2016 11:06:31 22.11.2016 11:06:31