Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
OPERATING LIMITS of the unit:
Minimum
air
temperature
-15°C *
Maximum air temperature :
50°C
Maximum differential pressure
between the two fluids: 2000Pa
* With external air temperature
< 0°C the microprocessor con-
troller intervenes to reduce the
risk of formation of frost within
the heat recovery unit. If the
temperature is <-15°C the mi-
croprocessor controller stops
the unit operation.
RePuro350RPD
22
IREPLJ - 1302 - 4238060_02
8.
GENERAL WARNINGS
The AERMEC RePuro units are manufac-
tured in accordance with recognised
:
technical standards and safety regula-
tions. They are designed for the renewal
and treatment of ambient air, and they
must be used for the purpose for which
they are intended and their perfor-
mance characteristics. All contractual
and extra-contractual liabilities causing
damage to persons, animals or objects
or through errors of installation, control
or maintenance or from improper use
are excluded by the Company. Any
uses not expressly indicated in this man-
ual are not permitted.
8.1.
CONSERVATION OF DOCUMENTA-
TION
Consign the instructions with all the
complementary documentation to the
user of the accessory who will assume
responsibility for the conservation of
the instructions so that these are always
available in case of need.
Carefully read this document. The ex-
ecution of all the works must be car-
ried out by qualified personnel, in ac-
cordance with the national regulations.
(D.M. 329/2004).
It must be installed in such a way to
make maintenance and/or repair func-
tions possible.
Do not modify or tamper with the ac-
cessory as this may cause danger for
which the manufacturer will not accept
any responsibility for damages caused.
The warranty is voided if the above in-
structions are not followed.
9.
PRODUCT IDENTIFICATION
The RePuro air heat recovery units are
identified through:
PACKING LABEL
that records the product identifica-
tion data.
TECHNICAL LABEL
technical label
8.2.
SAFETY WARNING AND INSTALLA-
TION STANDARDS
The unit must be installed by a
competent and qualified techni-
cian, and in accordance with the
legislation applicable in the coun-
try of installation (D.M. 329/2004).
AERMEC assumes no responsibility for
damage caused by failure to observe
these instructions.
Instructions essential for the proper in-
stallation of the equipment are shown
here. The final touches to all the op-
erations are however left to the expe-
rience of the installation engineer in
accordance with the specific needs.
Before commencing any works it is
necessary to CAREFULLY READ THE IN-
STRUCTIONS AND MINIMISE ANY RISKS
BY TAKING APPROPRIATE SAFETY PRE-
CAUTIONS.
All relevant personnel must be made
aware of the procedures and possi-
ble risks that may arise at the time of
installation of the unit.
The unit must be installed in such a
way as to make easy ordinary main-
tenance (filter cleaning) and special
maintenance as well as access to the
heat exchanger.
WARNING! : It is absolutely for-
bidden the operate the unit with-
out the 4 nozzles connected to
the ducting system.
DANGER : The fan is located
immediately beneath the noz-
zles. It is absolutely forbidden to
insert hands or objects. Power the unit
only after the 4 nozzles are connected
to the ducting system.
WARNING: The tampering, re-
moval or absence of the identifi-
cation label renders difficult any
operation of installation or main-
tenance.
example of technical label:
MODELLO
RePuro350R
MODEL
Numero di serie
YYMMLLPPPPPPXXXX
Serial Number
Numero Commessa
000000
Purchase Order
Tensione nominale
Frequenza Nominale
230V
Rated Voltage
Rated Frequency
Potenza Assorbita Nominale
Corrente Assorbita Nominale
180W
Rated Power Input
Rated Current Input
Potenza Assorbita Nominale con resistenza
180W
Rated Power Input with electric heater
Potenza Assorbita Nominale con resistenza
1.6A
Rated Power Input with electric heater
VERSIONE
00
VERSION
Peso
20kg
IPxx
Weight
50Hz
1.6A
0000000_00
Werbung
Kapitel
Inhaltsverzeichnis
