Riding Instructions; How To Ride; Setting The Hmi Modes - Mando footloose Handbuch

Mando Footloose user manual

Riding instructions

How to ride

Mando Footloose allows two ways of riding.
1. Riding Mando Footloose by pedaling
Start Mando Footloose off by pedaling as if so for general bikes.
Mando Footloose accelerates proportionally to the number of pedal rotations.
2. Riding Mando Footloose by throttling
Start Mando Footloose off by pushing the throttle lever slowly with your
thumb. Mando Footloose accelerates proportionally to the degree of pushing
the throttle lever.
Click
1) Install the HMI to the 2) Fix the position by pushing
holder on the handlebar. it completely until you hear
a Click
Description of the HMI screen
HMI Main Screen
MODE SELECT
The function of the automatic transmission may be affected by the body weight of
a rider, road condition, slope of the road and / or wind.
10
A new way of moving
E-1
Riding instructions

Setting the HMI Modes

Ensure that the number of pedal rotations
does not exceed 90 rpm (rotations per min-
ute). Excessive number of rotations may re-
duce the lifetime and cause breakdown of
the product due to overload.
The optimal range of the number of pedal
rotations is 30~60 rpm (charging information
-> Automatic transmission)
appears on the screen when the number of
pedal rotations is greater than 30 rpm).
Check the degree of acceleration force by
operating the throttle lever. Injudicious oper-
ation of the throttle may cause an accident.
Do not operate the throttle in situations other
than riding (e.g.when rolling Mando Foot-
loose or standing).
The maximum speed should not exceed
the maximum speed regulated in each
country, even when throttle lever is pushed
to its deepest point (when it is accelerating
to its maximum). The maximum speed may
vary with slope of the road, a head wind,
the body weight of a rider and/or charging
status.
E-2
Transmission settings
Auto: automatic transmission
Manual: manual transmission
Riding settings (applicable only when
pedaling)
Eco: slow acceleration / low battery use
Normal: average acceleration / average
battery use
Hard: fast acceleration / high battery use
Pedaling settings
Alarm
Soft: smooth pedaling / low power generation
Medium: normal pedaling / normal power
generation
1. Alarm for the remaining battery capacity
Hard: heavy pedaling / high power generation
Independent power generation
Power generated from the alternator by pedaling
Current speed
Current riding speed (km/h)
Trip distance Mileage (km)
*Initializing the mileage: Push the 'Select' but-
ton for more than 2 seconds.
Remaining amount of battery
Current remaining amount of battery
'Mode' button
Use to change between modes Charge the battery as soon as possible if the screen in the
'Select' button picture above appears.
Search the menu to select one of the following:
Automatic transmission set 1 -> auto trans-
mission set 2 -> setting Riding mode -> Ped-
aling mode (repeated)
'Power On/Off' button
Power On/Off (turning the bike on/off). Push the
button for more than a second to turn it on / off.
Total cumulative mileage
Total cumulative mileage
'Select' button
Transmission setting 1
(Manual transmission
Transmission setting 2
(Automatic transmission
-> Manual transmission)
Riding settings
(Riding by pedaling only)
Slow acceleration
/ low battery use
Pedaling settings
Smooth pedaling
/ low power generation
- When the product is turned on, it is automatically set to 'Auto' for transmission setting, 'Normal' for riding settings and 'Soft' for pedaling settings.
- The 'Auto' mode of the transmission setting allows for automatic transmission, and it is automatically set to Auto 2 when turned on and as Auto 1 when going
down a slope.
: Mando Footloose has an alarm function that shows a critical status of the product.
Please charge
Low Battery
the battery
English
E-3
'Mode' button
Automatic transmission
Manual transmission
Low speed / high torque High speed / low torque
Fast acceleration
/ high battery use
if under the same rpm (number of pedal rotations)
Heavy pedaling
/ high power generation
if under the same rpm (number of pedal rotations)
2. When the product has a problem (may be self-detected)
HMI
When the product has a problem, a red warning sign will
appear in the top right area as shown in the picture above.
If the warning sign does not disappear after turning the
HMI on / off (more than once), stop using the product and
contact the store.
11