Bosch GLM 100 C Professional Originalbetriebsanleitung Seite 27

OBJ_DOKU-36146-003.fm Page 27 Friday, February 19, 2016 9:59 AM
To recall the stored measurements, press
button 7. The result of the last measure-
ment is indicated on the display, along
with the indicator for the measured-value
list e and the memory location of the dis-
played measurements.
When no further measurements are
stored after pressing button 7 again, the measuring tool
switches back to the last measuring function. To exit the
measured-value list, press one of the measuring-mode but-
tons.
To continuously save the currently displayed length measure-
ment value as a constant, press and hold the measured-value
list button 7 until "CST" is indicated on the display. A mea-
sured-value list entry cannot be subsequently saved as a con-
stant.
To use a length measurement value in a measuring mode (e. g.
area/surface measurement), press the measured-value list
button 7, select the desired entry and confirm by pressing the
result button 6.
Deleting Measured Values
Briefly pressing button 4 deletes the last individual measuring
value determined in any measuring function. Briefly pressing
the button repeatedly deletes the individual measuring values
in reverse order.
To delete the currently displayed measured-value list entry,
briefly press button 4. To delete the complete measured-val-
ue list and the constant "CST", press and hold the measured-
value list button 7 and at the same time briefly press button 4.
In wall surface measurement mode, briefly pressing button 4
the first time deletes the last individually measured value;
pressing the button a second time deletes all lengths B
pressing the button a third time deletes the room height A.
Adding Measured Values
To add measured values, firstly carry out any measurement or
select an entry from the measured-value list. Then press the
plus button 11. For confirmation, "+" appears on the display.
Then carry out a second measurement or select another entry
from the measured-value list.
To call up the sum of both measurements,
press the result button 6. The calculation
is indicated in the measured-value lines a,
and the sum in the result line c.
After calculation of the sum, further
measured values or measured-value list
entries can be added to this result when
pressing the plus button 11 prior to each measurement.
Pressing the result button 6 ends the addition.
Notes on the addition:
– Mixed length, area and volume values cannot be added to-
gether. For example, when a length and area value are add-
ed, "ERROR" briefly appears on the display after pressing
the result button 6. Afterwards, the measuring tool switch-
es back to the last active measuring mode.
– For each calculation, the result of one measurement is
added (e.g. the volume value); for continuous measure-
ments, this would be the displayed measured value in re-
Bosch Power Tools
sult line c. The addition of individual measured values from
the measured-value lines a is not possible.
Subtracting Measured Values
To subtract measuring values, press mi-
nus button 5; For confirmation, "–" is in-
dicated on the display. The further proce-
dure is analog to "Adding Measured
Values".
Data Transmission to other Devices
The measuring tool is equipped with a Bluetooth® module,
which enables data transmission via radio technology to cer-
tain mobile terminals/devices with a Bluetooth® interface
(e.g., smartphones, tablets).
For information on the necessary system requirements for a
Bluetooth® connection, please refer to the Bosch website at
www.bosch-pt.com
For data transmission via Bluetooth®, time delays between
mobile terminal/device and measuring tool may occur. This
can be possible due to the distance between both devices or
the object being measured.
Data transmission to certain other devices with USB interface
is possible via the measuring tool's micro USB port (e.g. to
computers, notebooks). In USB operation, the charging dura-
tion n can be significantly prolonged during data transmis-
sion.
Activating the Bluetooth® Interface for Data Transmission
to a Mobile Terminal/Device
To activate the Bluetooth® interface, press the measuring
tool's Bluetooth® button 13. Make sure that the Bluetooth® in-
, and terface on your mobile terminal/device is activated.
X
Special Bosch applications (apps) are available to extend the
functional range of the mobile terminal/device and for simpli-
fication of the data processing. Depending on terminal/de-
vice, these can be downloaded at the respective app stores:
After starting the Bosch application, the connection between
the mobile terminal/device and the measuring tool is estab-
lished. When several active measuring tools are found, select
the appropriate measuring tool. When only one active meas-
uring tool is found, the connection is automatically estab-
lished.
Note: When establishing the connection between the meas-
uring tool and the mobile terminal/device (e.g., smartphone,
tablet) the first time (pairing), the measuring tool's PIN code
may be requested. In this case, enter "0000".
English | 27
1 609 92A 25T | (19.2.16)