Princeton Tec VIZZ TACTICAL Bedienungsanleitung

VIZZ TACTICAL
®
&
VIZZ TACTICAL
®
MPLS
Operating and Maintenance
Instructions
ENGLISH:
Battery Installation - See Figure 1
3 AAA • Alkaline (LR03)
• Lithium (L92)
• Rechargeable NiCad or NiMH
Princeton Tec cares about the environment and recom-
mends recycling batteries. For more information about bat-
tery recycling, please go to www.batteryrecycling.com.
Observe proper battery polarity. Improper installation of the
batteries will damage the light and void the warranty.
!
WARNING
• Never mix fresh and used batteries.
• Never mix different battery brands or chemistry types
• Always remove drained batteries immediately.
• Remove batteries during long periods of storage.
NOTE: Lithium batteries offer extended constant brightness
time, extreme cold weather performance, and lighter
weight. Rechargeable NiCad or NiMH batteries may result in
reduced brightness due to lower nominal voltage.
The Vizz battery compartment has a waterproof seal. It is
important to keep this seal free from dirt and away from
harsh chemicals in order to preserve waterproof integrity.
Inspect the seal every time batteries are changed. If dirt
is present, wipe gently with a damp cotton swab and mild
soap until dirt is removed.
Switch Operation - See Figure 2
From off:
One press: red LED.
Double press: green LED.
Triple press: blue LED.
Note: color mode is user configurable. See "Configuring
Color Mode" below.
Two second press: IR
Five second hold: lock or unlock the headlamp
From any visible color mode (red, green, blue) a two second
hold turns on the white Maxbright LED at high output.
From this state, releasing then holding the button initiates
dimming of the white mode.
From any mode, a single press of the button turns the
headlamp off.
Removal and replacement of batteries will also reset Vizz to
unlocked state.
Configuring Color Mode
Eight second hold: enter/leave programming mode
Note: The selected initial color mode flashes during
programming. Default order: red > green > blue. Each button
press advances to the next mode. Leaving the programming
mode via eight second press sets active mode to turn on
with one button press.
Troubleshooting
If the Vizz fails to light:
• Check the batteries for proper installation.
• Replace batteries if proper installation is confirmed.
• Check circuit board for water (the seal may have be com-
promised by improper rear cover installation or dirty seal).
The light will resume normal operation once the water is
shaken or blown out and the light is left open until com-
pletely dry. If the light has been contaminated with salt
water, flush the unit with fresh water and dry as described
above.
Figure 1 – Battery Replacement – Vizz Tactical, Vizz Tactical MPLS
1
0318
Figure 2 – Switch Operation – Vizz Tactical, Vizz Tactical MPLS
SINGLE PRESS
RED ULTRABRIGHT LED
(default)
DOUBLE PRESS
GREEN ULTRABRIGHT LED
(default)
TRIPLE PRESS
BLUE ULTRABRIGHT LED
(default)
1 SECOND HOLD
IR
5 SECOND HOLD
LOCK / UNLOCK
3 flashes indicate lock / unlock
Figure 3 – Program – Vizz Tactical, Vizz Tactical MPLS
8 SECOND HOLD
ENTER / LEAVE
PROGRAMMING MODE
Figure 4 – Mounting System - Vizz Tactical MPLS
1
Vizz Tactical MPLS Accessories
To attach the Vizz Tactical MPLS to the NVG Shroud:
1. Slide the bracket arm into the NVG Shroud adapter plate,
making sure the pull tab is above the lip of the adapter
plate and that the male grooves on the bottom of the
bracket arm are aligned inside the female grooves on the
bottom of the adapter plate.
2. Push the bracket arm securely into place, ensuring that
the pull tab audibly clicks over the lip of the NVG Shroud
adapter plate.
3. Your MPLS Headlamp should now be secured in the NVG
Shroud. You can rotate the headlamp to focus your light
source accordingly.
To remove the MPLS headlamp from the NVG Shroud:
1. Remove the NVG Mount from your helmet.
2. Push up slightly on the bottom of the light housing.
3. While pushing upward, use the tool on the provided
headstrap to press the tab of the arm bracket towards
the headlamp housing, so that it disengages from the
NVG Shroud adapter plate.
4. Slide the headlamp unit out of the NVG Shroud adapter plate.
To attach the MPLS Headlamp to the Butterfly Mount:
1. Slide the bracket arm into the Butterfly Mount, making
sure the pull tab is above the lip of the mount and that
the male grooves on the bottom of the bracket arm are
aligned inside the female grooves on the bottom of the
mount.
2. Push the bracket arm securely into place, ensuring that
the pull tab audibly clicks over the lip of the Butterfly
Mount.
3. Your MPLS Headlamp should now be secured in the
Butterfly Mount. The mount can be attached to the
provided headstrap, MOLLE straps, or any 1" webbing.
You can rotate the headlamp to focus your light source
accordingly.
To remove the MPLS headlamp from the Butterfly Mount:
1. Push up slightly on the bottom of the light housing.
2. While pushing upward, use the tool on the provided
headstrap to press the tab of the arm bracket towards
the headlamp housing, so that it disengages from the
Butterfly Mount.
3. Slide the headlamp unit out of the Butterfly Mount.
USA Lifetime Warranty - International 10-YearWarranty
Due to International regulations, Princeton Tec's lifetime
warranty can only be offered to customers in the USA.
Princeton Tec offers a 10-year warranty to our customers
outside the USA. FULL WARRANTY - Princeton Tec warrants
2 3
From any visible color mode
2 SECOND HOLD-
WHITE ULTRABRIGHT LED
From white Maxbright mode
SINGLE PRESS
SELECT COLOR MODE
selected color flashes rapidly
2 1
this product to be free from defects in workmanship and
materials under normal use for as long as you own this
product. This warranty covers all of the component parts of
the product except batteries. This warranty does not cover
deterioration due to normal wear or damage due to misuse,
alteration, negligence, accidents, or unauthorized repair.
Princeton Tec will repair or replace parts which are defective
In workmanship or materials. Your authorized Princeton Tec
Dealer and Princeton Tec are the only facilities authorized to
repair the product. After (3) unsuccessful attempts to repair
the product, you have the right to elect replacement of the
product or a refund of the purchase price less allowance for
use of the product. NO INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARE INCLUDED IN THIS WARRANTY. (Some
states do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitations or
exclusions may not apply to you.) This warranty gives you
specific legal rights, and you may also have other rights
which vary from state to state.
Princeton Tec reserves the right to change product
specifications without notice.
FOR CALIFORNIA RESIDENTS:
WARNING: This product contains Bisphenol A (BpA) a
chemical known to the State of California to cause birth
defects or other reproductive harm.
Return Policy
If your light fails to operate, follow these simple steps:
1. Check batteries. Replace if necessary.
2. To send your light in for repair or replacement, first
contact Princeton Tec customer service on
1-800-257-9080 to request an RMA number. Please
have your light model, date of purchase and a brief
description of the fault you are experiencing. No
warranty repairs will be accepted without an RMA
number.
3. Return the light without batteries to:
Princeton Tec, PO Box 8057 Trenton NJ 08650.
Postage due and freight collect items will not be
accepted.
4. Upon receipt your light will be processed in about
two weeks. Please allow additional time for return
transportation from NJ.
Princeton Tec
PO Box 8057 ,
Trenton, NJ 08650
Phone: 609-298-9331
Fax: 609-298-9601
princetontec.com
© 2018 Princeton Tec
4
HOLD
DIMMING
Dimming
From any mode
OFF
PRESS
2