Assembly Components - Alpina MP 24 Li Gebrauchsanweisung

comply with these instructions to
avoid serious risks or hazards.
For storage and transport purposes, some
components of the machine may not be installed
in the factory and have to be assembled after
unpacking. Follow the instructions below.
Unpacking and completing the assembly
should be done on a flat and stable surface,
with enough space for machine handling
and its packaging, always making use of
suitable equipment. Do not use the machine
until all the indications provided in the
"ASSEMBLY" section have been carried out.

4.1 ASSEMBLY COMPONENTS

The packaging includes assembly components.
4.1.1 Unpacking
1. Cautiously open the packaging, paying
attention not to lose components.
2. Consult the documentation in the
box, including these instructions.
3. Remove all the unassembled
parts from the box.
4. Remove the machine from the box.
5. Dispose of the box and packaging in
compliance with local regulations.
4.2 ASSEMBLY OF THE GUIDE
BAR AND TOOTHED CHAIN
Always wear heavy-duty gloves when
handling the bar and chain. Mount the
bar and chain very carefully so as not to
impair the safety and efficiency of the
machine. If in doubt, contact your dealer.
Perform all operations after
removing the battery.
1. Unscrew the knob (Fig. 3.A) and
remove the chain guard (Fig. 3.B), to
access the drive pinion and bar seat.
2. Mount the bar (Fig. 4.A) by inserting
the stud bolt (Fig. 4.B) in the groove
(Fig. 4.C) and push it towards the
back of the machine body.
3. Mount the chain around the drive pinion (Fig.
5.A) and along the bar guide, being careful
to follow the sliding direction (Fig. 5.B).
If the tip of the bar is equipped with
a nose sprocket, make sure the
Direction in which
the chain runs
drive links are correctly inserted
in the sprocket rims (Fig. 6.).
4. Check that chain tension adjuster pin (Fig.
5.C) is fitted properly in the hole on the bar;
if it isn't, turn the chain tension knob (Fig.
5.D) until the pin is completely inserted.
5. Replace the guard without
fully tightening the knob.
6. Turn the chain tension knob (Fig. 5.D) to
achieve the desired tension (Fig. 7).
7. Raise the bar and tighten the
guard knob (Fig. 8.A).
4.2.1 Checking the chain tension
Check the chain tension.
The tension is correct when the drive links
do not slip out of the chain guides if you hold
the chain in the middle of the bar (Fig. 7).
4.3 FITTING THE PRUNER DEVICE
Perform all operations after
removing the battery.
The pruner device (Fig. 9.A) can be mounted
directly on 'commands rod (Fig. 9.B) so
as to achieve the standard length.
• Insert the commands rod (Fig. 9.B) in
the auction device pruner (Fig. 9.A).
• Slide the collar (Fig. 9.C) upwards and turn
it clockwise until it is completely tightened.
Periodically check the connections to
ensure that they are tightened securely.
4.4 EXTENSION OF PRUNER DEVICE
The maximum reach can be achieved
by fitting the extension tube (Fig. 10.A
between the commands rod (Fig. 10.B)
and the pole pruner device (Fig. 10.C).
• Slide the collars (Fig. 10.D) up and rotate it
clockwise until it is completely tightened.
Periodically check the connections to
ensure that they are tightened securely.
4.5 REMOVING THE PRUNER DEVICE
If the extension tube (Fig. 10.A) is
fitted, the pruner device (Fig. 10.C)
must be removed at first.
• To remove the pruner device ((Fig. 10.C),
rest the comands rod (Fig. 10.B) on the
ground, loosen the collar (Fig. 10.D)
and remove the pole pruner device.
EN - 7