Operation Via A Light Controller - IMG STAGE LINE DAZZLER LED-200DX/RGB Bedienungsanleitung

6.2 Remote control LC-3
GB
The remote control LC-3 available as an accessory
allows to control various functions in addition to the
music control.
1) Connect the remote control to the jack ONLY FOR
REMOTE CONTROL (7).
2) There must be no DMX signal at the DMX INPUT
(4).
3) Via the DMX
200DX/RGB or LED-200DX/WS units may be con-
nected ( chapter 6.1) in order to control them
together with the master unit via the remote control.
4) The button STAND BY (13) allows to activate/deac-
tivate the light beams. With the beams deactivated,
the LED next to the button STAND BY will light up.
5) Select the operating mode with the button MODE
(15).
a) After switching on the light effect unit, the Stro-
boscope mode will be activated. The LED next
to the button MODE will be off.
As long as the button FUNCTION (14) is kept
pressed, one of the three stroboscope functions
will be activated:
1. Stroboscope independent of the music
2. Stroboscope light sequence independent of
the music (when several LED-200DX/... units
are interconnected)
3. Music-dependent stroboscope
When the button FUNCTION is kept pressed
again, the next stroboscope function respec-
tively will be activated.
b) To switch to the Chase mode, press the button
MODE once. The LED next to the button will light
up. Press the button FUNCTION to select:
– model LED-200DX/RGB: permanent light or
music-dependent light control programme
– model LED-200DX/WS: permanent light or
three music-dependent light control pro-
grammes
10
OUTPUT (8), further

7 Operation via a Light Controller

For operation via a light controller with DMX512 proto-
col (e. g. DMX-1440 or DMX-510USB by "img Stage
Line"), model LED-200DX/WS is equipped with one
DMX control channel and model LED-200DX/RGB
with four control channels. The functions of the chan-
nels and the DMX values can be found in chapter 8.1.
7.1 Connection
LED-
As a DMX interface, the light effect unit is provided with
3-pole XLR jacks of the following pin configuration:
Pin 1 = ground, 2 = DMX-, 3 = DMX+
For connection, special cables for high data flow should
be used. Standard microphone cables with screening
and a minimum cross section of 2 × 0.22 mm
a capacity as low as possible can only be recom-
mended for a total cable length of up to 100 m. For
cable lengths exceeding 150 m it is recommended
to insert a DMX level matching amplifier (e. g.
SR-103DMX by "img Stage Line").
1) Connect the DMX input (4) to the DMX output of the
light controller.
2) Connect the DMX output (8) to the DMX input of the
following light effect unit; connect its output again to
the input of the following unit, etc. until all light effect
units have been connected in a chain.
3) Terminate the DMX output of the last DMX unit in
the chain with a 120 Ω resistor (> 0.3 W): Solder the
resistor to the pins 2 and 3 of an XLR plug and con-
nect the plug to the DMX output or use a corre-
sponding terminating plug (e. g. DLT-123 by "img
Stage Line").
7.2 Adjusting the start address
For operating the LED-200DX/... with a light controller,
adjust the DMX start address for the first DMX channel.
If e. g. address 17 on the controller is provided for con-
trolling the light effect unit, adjust the start address 17
on the LED-200DX/.... For model LED-200DX/RGB,
the DMX channels 2 – 4 will then automatically be
assigned to the three following addresses (in this
example 18 – 20). As the next possible start address for
the following DMX-controlled unit, address 21 could be
used in this example.
The start address is adjusted as a binary number
with the DIP switches Nos. 1 – 9 (9). It will result by
adding the place values of the switches set to "ON".
2 and with