Safety Instructions - STEINEL 750 serie Bedienungsanleitung

Principle
The CeilingSensorLight is light on automatically. No
heat radiation is detected
equipped with three 120°
pyro sensors which detect the through obstacles, such as
invisible heat emitted by mov- walls or glass and no
ing objects (pedestrians, ani- switching therefore occurs.
mals etc.). The heat detected Pyro sensors have a detec-
is converted electronically tion angle of 360° with an
opening angle of 180°.
into a signal that switches the

Safety instructions

a
switch off the power first
Disconnect the power
and check freedom from
supply before any work on
voltage with a voltage
the CeilingSensorLight!
a
tester.
During installation, the
a
electric power cable to be Installation of the
CeilingSensorLight
connected must be
involves work on the
voltage-free. Therefore,
Installation
The installation site should be For exposed wiring
at least 50 cm from another
drill the hole for insertion of
light, since the latter's heat
the cable and deburr with a
radiation could result in false
round file.
triggering of the sensor.
4. Screw on housing
Furthermore, the Ceiling-
at a right angle if required
SensorLight must be position-
by means of the elongated
ed completely on the attach-
holes.
ment surface.
5. Connection of the mains
lead (see diagram).
Installation procedure:
1. Hold housing against
The mains lead consists of a
the wall and mark drill
3 phase cable (dia. 10 mm
holes at the markings.
max.).
2. Drill the holes and insert
wall plugs (6 mm dia.).
L = phase conductor
3. Remove the coating of the
(usually black
mains lead to max. 2 cm
or brown)
and push the enclosed
N = neutral conductor
heat-resistant silicone
(usually blue)
sheaths on to the insulated
PE = protective-earth
strands. Insert sealing
conductor
plugs in the housing,
(green/yellow)
pierce and pass the cable
through.
12
Important: the safest motion
detection is obtained when
the device is mounted lateral-
ly to the walking direction and
no obstacles (such as trees
and walls, for example) ob-
struct the view .
mains power supply; this
work must therefore be
carried out professionally
in accordance with
regulations.
: If in doubt, the cable must be
identified with a voltage test-
er. Switch off the current
again. The phase (L) and
neutral conductors (N) are
, align
connected to the terminal
block. Connect the protect-
ive-earth conductor to the
corresponding terminal.
Note: A mains switch for ON
and OFF switching can of
course be installed in the
mains lead. This is a pre-
requisite for permanent light
function (refer to permanent
light function section,
page 14).
6. Apply the lampshade
and secure by rotating.
7. Perform time, light
threshold and bright-
ness control adjustment
(refer to functions section,
page 13).
Functions
put into operation. After remo-
Once you have installed the
ving the decorative ring
housing and connected the
the adjusting screws for twi-
CeilingSensorLight, it can be
2 - 2000 lux approx. 5 sec. - 15 min.
Twilight setting Switch-off delay
(threshold) (time setting)
Continuously adjustable light
Continuously adjustable
duration of 5 sec. to 15 min.
sensor response threshold
from 2 – 2000 lux.
Adjustment control set to 1
= shortest time
Adjustment control set to 1
(5 sec., factory setting)
= daylight operation, approx.
2000 lux. (factory setting)
Adjustment control set to 6
= longest time (15 min.)
Adjustment control set to 6
= night-time operation
When setting the detection
approx. 2 lux.
zone, it is recommended to
select the shortest time
The adjustment control must
(setting 1).
be set to 1 (daylight
operation) when setting the
detection zone in daylight.
Soft light illumination
The CeilingSensorLight has a
output when switched on, but
soft light illumination function. the brightness is slowly incre-
This means that the light
ased to 100% within two se-
does not switch directly to full conds. The electronics opera-
light, time and brightness
control are visible.
0 - 50 %
Brightness control
(Watt-o-matic)
Continuously adjustable con-
stant light from 0 – 50 %.
When movement is detected,
the light switches from, say,
20 watts maintained light
output to maximum output
(100 watts).
Adjustment control set to 1
= no dimming (factory setting)
Adjustment control set to 6
= greatest dimming
If this control is rotated, the
red LED (behind the lens)
flashes and the light illumin-
ates with the set brightness.
After release, the dimming
level can be further adjusted
for approx. 3 sec. (LED con-
tinues to flash).
te equally gently when swit-
ching off.
13