Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
G Operating instructions
AV Radio Transmission System 5.8 GHz
Item no. 94 23 57
Intended Use
The radio transmission system is intended for wireless transmission of video, audio and infrared si-
gnals around the home and is suitable for audio and video devices customarily use in households.
The transmitter and receiver are only approved for connection to the wall plug transformers supplied.
The wall plug transformers are only suitable for use with normal household mains sockets with
230 V/AC, 50 Hz alternating voltage.
The entire system must only be used in indoor rooms. Do not use it outdoors. Contact with moistu-
re, for example in bathrooms, must be avoided.
Any other use than that described above, could lead to damage to this product and involves the
risk of short circuits, fire, electric shock, etc.
Please observe the regulations concerning radio operation in your country when using this product.
No part of the product may be modified or rebuilt and the housing must not be opened.
The safety instructions must be observed at all times.
This product complies with the applicable National and European specifications.
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe these
safety instructions. We do not assume liability for any resulting damage.
We do not assume any liability for material and personal damage caused by improper
use or non-compliance with the safety instructions. The warranty will be void in such
cases.
• For safety and approval (CE) reasons, unauthorised conversion and/or modifications to the pro-
duct are not permitted.
• The wall pug transformer provided is constructed according to protection class II.
• Only connect the wall plug transformers to standard mains sockets (230 V~ / 50 Hz). The actual
radio transmission system is only to be supplied with energy via the enclosed wall plug transfor-
mers.
• The power sockets to which the power adapters are connected must be easily accessible.
• To disconnect the radio transmission system completely from the mains, the wall plug transfor-
mers must be disconnected from the mains sockets.
• Never replace a damaged power cable. If the connecting cable is damaged, the power unit is
unusable and must be disposed of. Do not repair.
• Devices, operated by the mains voltage, must be kept out of the reach of children. For this rea-
son, be particularly cautious when using the system in the presence of children. They may try
to poke objects into it through openings in the housing. There is danger of a life-threatening
electric shock.
• Check the radio transmission system from time to time for damage. Do not touch a power pack,
the transmitter, the receiver or the connection cables if they show signs of damage. First, switch
off the corresponding power socket completely (remove the corresponding fuse or switch off
the automatic circuit-breaker, then switch off the earth-leakage trip) and then pull the power
adapter carefully out of the power socket. Do not operate the product after that, but take it to a
specialised workshop.
• Never place vessels or containers containing liquids, such as glasses, buckets, vases or plants,
in the immediate vicinity of the system. Liquids may seep into the casing and thus impair the
electrical safety of the device. Furthermore, there is a significant risk of fire or of a lethal elec-
tric shock! In such an event, isolate the mains socket, to which the product is connected (e.g.
switch off the automatic fuse), and unplug the wall plug transformer from the mains socket.
Afterwards, the product can no longer be used; take it to a specialist workshop.
• Do not expose the system to high temperatures, humidity, dripping or sprayed water, strong
vibrations or heavy mechanical loads.
• Do not place naked flames, such as burning candles, on or close to the system.
• If you have doubts about how the equipment should be operated or how to safely connect it,
consult a trained technician.
• Do not leave packing materials unattended. It may become a dangerous plaything for children.
• Never leave the system running unsupervised.
• Do not use the system in a tropical climate.
• Observe the safety and operating instructions of any other devices that are connected to the
radio transmission system as well as the other safety instructions in the individual chapters of
these instructions.
• If in doubt about how to connect the device correctly, or should any questions arise that are
not answered in these operating instructions, please contact our technical advisory service or
another specialist.
Product Description
The radio transmission system consists of a transmitter and a receiver.
The sender receives the audio and video signals from the AV source device (e.g. DVD player) and
converts these into a 5.8 GHz radio signal. The receiver receives this radio signal and converts it
back to the original audio and video signals.
At the same time, the receiver converts the infrared remote control signals into a radio signal and
sends them back to the transmitter.
Based on the technique described above, both audio/video signals and the control signals from
infrared controls can be transmitted without cables and through walls.
The signals from the AV source can then be reproduced in another room on a device (e.g. TV set)
located there and, in addition, the AV source can be controlled from there by means of its remote
control.
DVD
12:55
1
2
3
VHS VIDEO
4
5
6
27.
09.98
7
8
9
0
SAT
EuroSk y
1 5:59
DV B
CH
Digita l Video
Broadcastin g
M iniSa t 2
DIGI TA L RECEIVER
FREE TO AI R
Connection
This radio transmission system is only suitable for low-voltage video and audio sig-
nals. Only connect devices with such connections.
If in doubt, consult an expert.
If these instructions are not observed, the radio transmission system or connected
devices could be damaged.
a) Connecting Transmitter and Receiver
• Connect the enclosed AV line for the transmitter (labelled TRANSMITTER) to the AV IN socket
on the transmitter.
• Plug the Scart plug, on the other end of the AV line, into the Scart socket of the AV source (DVD
player, video recorder, SAT receiver etc.).
• Connect the enclosed AV line for the receiver (labelled RECEIVER) to the AV IN socket on the
receiver.
• Plug the Scart plug, on the other end of the AV line, into the Scart socket of the TV set.
b) Connecting the IR Cables
• Connect the IR receiver with the IR-R socket on the receiver.
• Place the IR receiver close to your TV, so it is within the transmission range of the remote control.
You can fix the IR receiver in place with the self-adhesive tape supplied.
• Connect the IR transmitter to the socket IR-T on the transmitter (labelled „WIRELESS TRANS-
MITTER" on the name plate).
• Using the enclosed adhesive pads, attach the IR transmission diodes to the IR receiving sensors
on the devices you want to control.
• Leave an area around the IR receiver sensors free, so the devices can still be controlled by the
remote control.
The position for the IR receiving sensor, on the device you want to control, can be seen
in the relevant operating instructions. A maximum of three devices can be connected.
c) Connecting the Power Units
Only use the enclosed wall plug transformers for connecting to the mains.
Only mains s ocket connected to the public grid may be used to power for the wall plug
transformers.
When making the connections, make sure that the connecting cables are not pinched
or damaged by sharp edges.
The mains sockets, to which the power units are connected, must be easily accessib-
le, so the wall plug transformers can be quickly removed from the mains voltage in the
case of a fault.
• Connect the low-voltage plug of the power adapters with the corresponding socket on the sen-
der and receiver.
Both power units are identical. Therefore, it is irrelevant which power unit is connected
to which device.
• Plug the power unit into the wall mains socket.
TV
AV
IR
Werbung
Inhaltsverzeichnis
