Caractéristiques D'entrée; Caractéristiques De Sortie - Conrad M1224 FX Bedienungsanleitung

B) Caractéristiques d'entrée
Impédance
Entrées
d´entrée
MIC
4kΩ
(Channels 1-4)
LINE
10kΩ
(Channels 1-4)
MIC
3kΩ
(Channels 5/6, 7/8)
Stéréo LINE
5kΩ
(Channels 5/6, 7/8, 9/10, 11/12)
INSERT connecteur 10kΩ
TAPE IN 10kΩ
C) Caractéristiques de sortie
Impédance
Sortie
de sortie
MAIN L/R 240Ω
ALT 3/4 75Ω
CONTROL ROOM L/R 75Ω
AUX SEND 75Ω
INSERT connecteur 600Ω
REC OUT 600Ω
HEADPHONE 100Ω
56
Impédance Niveau
Type de raccordement classique
nominale d´entrée
50 - 600Ω -50dB Connecteur Type XLR-3-31,symétrique
600Ω -30dB Prise de 6,35mm
600Ω -44dB Connecteur Type XLR-3-31,symétrique
600Ω -20dB Prise stéréo asymétrique de 6,35mm
600Ω 0dB Prise stéréo de 6,35mm
600Ω -10dBV Prise cinch
Impédance Niveau
Type de raccordement classique
nominale d´entrée
10kΩ +4dB Prise symétrique de 6,3 mm
10kΩ +4dB Prise asymétrique de 6,3 mm
10kΩ +4dB Prise asymétrique de 6,3 mm
600Ω +4dB Prise asymétrique de 6,3 mm
10kΩ 0dB Prise mono de 6,35mm
10kΩ -10dBV Prise cinch
33Ω 3mW Prise stéréo de 6,35mm
A8. PRE/ POST button
Press the button in ( ) to send pre-fader signal to the AUX bus,
so that the fader adjustment does not affect the AUX output.
Press the button again ( ) to send post-fader signal, after fader
adjustment, to the AUX bus.
A9. EFX control
Turn this knob to adjust the level of the post-fader signal sent from
that channel to EFX bus.
A10. PAN (1 to 4), BALANCE (5/6 to 11/12) control
The PAN control determines the stereo position of the channel
signal on the MAIN (L and R) buses and ALT 3/4 buses.
The BALANCE control sets the balance between left and right
channels. Signals input to the L input (odd channel) go to the
MAIN L bus or ALT 3 bus. The signals input to the R input (even
channel) go to MAIN R bus or ALT 4 bus.
A11. ALT 3/4/ MUTE button
Press the button to route the output signal to ALT 3/4 output in lieu
of MAIN L/R output. The button lights up to indicate the function
is activated.
A12. PFL (Pre-Fader Listen) button
Press the button in ( ) to send pre-fader output signal of that
channel to the "HEADPHONE" (D8) and "CONTROL ROOM
(L and R)" (D9) sockets for monitoring.
The LED next to the button lights up to indicate the PFL function
is activated.
A13. Channel fader
It adjusts the level of the channel signal send to the master mixing
(MAIN, ALT 3/4) buses, auxiliary (AUX) bus and effect (EFX) bus.
Set the fader of unused channel at the minimum position to prevent
undesired noise to the main programme signal.
29