Steam Ironing; Dry Ironing; Setting The Temperature - TEFAL GV7096 Bedienungsanleitung

1800121551 GV7096 GTK TEFAL_110 x 154 03/03/11 15:02 Page6
Use

Steam ironing

• Place the iron's temperature control dial according to the type of fabric to be ironed
(see table below).
• The thermostat light comes on. Be careful ! The steam generator is ready when the
thermostat light goes out and when the green "steam ready" light stays on.
• When the iron is in use, the iron thermostat light on the iron comes on and goes off
according to the soleplate temperature requirement without this having any effect
on the use of the appliance.
• To obtain steam, press on the steam control button under the iron handle and keep
it pressed - fig.5. The steam will stop when you release the button.
• Always spray starch onto the reverse side of the fabric to be ironed.
To prime the steam circuit, either
before using the iron for the first
time, or if you have not used the
steam function for a few mi-
nutes, press the steam control
button several times in a row,
holding the iron away from your
clothes. This will enable any cold
water to be ejected from the
steam circuit.
• Iron temperature setting:
- Start with the fabrics to be ironed at a low temperature (•) and finish with those which need higher
temperatures (••• or Max).
- Mixed fibre fabric: set the ironing temperature to the setting for the most delicate fabric.
- Woollen garments: press repeatedly on the steam control button -
without placing the iron on the garment itself.
ECO MODE: Your steam generator iron has an ECO mode function which uses less power whilst still
guaranteeing a sufficient steam flow for you to iron your washing properly. In order to use this
function, once the thermostat of your iron has been correctly set (see table above), press on the ECO
mode button located on the control panel. The ECO mode can be used on all types of fabrics,
nevertheless for very thick or very creased fabrics, we recommend that you use the normal steam flow
for best results.

Dry ironing

• Do not press the steam control button under the iron handle.
Recommendations : for fa-
brics other than linen or cot-
ton, hold the iron a few
centimetres from the gar-
ment to avoid burning the fa-
bric.
Refilling the water tank
• When the red "water tank empty" light starts flashing, it means that you have no more steam.-
The water tank is empty.
• Unplug the steam generator and open the flap on the tank.
• Pour in untreated tap water up to the max mark -
• Replug the generator. Press the "OK" button on the control panel -
light stops flashing, the steam is ready.
SETTING THE TEMPERATURE AND STEAM OUTPUT ACCORDING TO TYPE OF FABRIC TO BE IRONED:
T
YPE OF FABRICS
Synthetics , Silk
(polyester, acetate, acrylic, polyamide)
Wool, Viskoz
Linen, cotton
• Set the iron temperature control dial to the MAX position.
• Hang the garment on a coat hanger and hold the fabric slightly taut with one
hand.
As steam is very hot : never attempt to remove creases from a garment while
it is being worn, always hang garments on a coat hanger.
• Holding the iron in a vertical position, tilted slightly forwards, press repeatedly on
the steam control button -
from top to bottom - fig.6.
fig.4.
Do not place the iron on a
metal support.When ta-
king a break from ironing,
always place the iron on
the iron rest plate of the
unit. It is equipped with
non-slip pads and has
been designed to with-
stand high temperatures.

Setting the temperature

Setting temperature control
fig.5 to obtain short bursts of steam,
Vertical steam ironing
fig.5 (underneath the iron handle) moving the iron
fig.19. to continue ironing. When the green
EN
DE
FR
NL
ES
PT
IT
DA
NO
SV
FI
TR
EL
PL
CS
SK
HU
SL
RU
UK
HR
RO
fig.18.
ET
LT
LV
6