Beko WMY 71423 LMB3 Bedienungsanleitung Seite 71

4.12 child Lock
Use child lock function to prevent children from tampering
with the machine. Thus you can avoid any changes in a
running programme.
C
If the Programme Selection knob is turned when the
Child Lock is active, "Con" appears on the display.
The Child Lock does not allow any change in the
programmes and the selected temperature, speed and
auxiliary functions.
C
Even if another programme is selected with the
Programme Selection knob while the Child Lock is
active, previously selected programme will continue
running.
C
When the Child Lock is active and the machine is
running, you can switch the machine to Pause mode
without deactivating the Child Lock by turning the
Programme Selection knob to On / Off position. When
you turn the Programme Selection knob afterwards, the
programme will resu
To activate the child Lock:
Press and hold 1st and 2nd Auxiliary Function buttons for
3 seconds. The lights on the 1st and 2nd Auxiliary Function
buttons will flash while you keep the buttons pressed for 3
seconds.
To deactivate the child Lock:
Press and hold 1st and 2nd auxiliary function buttons for 3
seconds while any programme is running. The lights on the
1st and 2nd Auxiliary Function buttons will flash while you
keep the buttons pressed for 3 seconds.
C
In addition to the method above, to deactivate the Child
Lock, switch the Programme Selection knob to On /
Off position when no programme is running, and select
another programme.
C
When the power is restored after a power failure or after
your machine is unplugged and plugged in again, the
Child Lock will not be deactivated when the machine
resumes operating.
4.13 Progress of programme
Progress of a running programme can be followed from the
Programme Follow-up indicator. At the beginning of every
programme step, the relevant indicator light will turn on and
light of the completed step will turn off.
You can change the auxiliary functions, speed and
temperature settings without stopping the programme flow
while the programme is running. To do this, the change
you are going to make must be in a step after the running
programme step. If the change is not compatible, relevant
lights will flash for 3 times.
C
If the machine does not pass to the spinning step,
Rinse Hold function might be active or the automatic
unbalanced load detection system might be activated
due to the unbalanced distribution of the laundry in the
machine.
4.14 Loading door lock
There is a locking system on the loading door of the
machine that prevents opening of the door in cases when
the water level is unsuitable.
Loading door light will start flashing when the machine
is switched to Pause mode. Machine checks the level of
the water inside. If the level is suitable, Loading Door light
71 / EN
illuminates steadily within 1-2 minutes and the loading door
can be opened.
If the level is unsuitable, Loading Door light turns off and the
loading door cannot be opened. If you are obliged to open
the Loading Door while the Loading Door light is off, you
have to cancel the current programme; see "Canceling the
programme".
changing the selections after programme has
started
switching the machine to pause mode
Press the Start / Pause button to switch the machine to
pause mode while a programme is running. The light of
the step which the machine is in starts flashing in the
Programme Follow-up indicator to show that the machine
has been switched to the pause mode.
Also, when the loading door is ready to be opened, Loading
Door light will also illuminate continuously in addition to the
programme step light.
changing the speed and temperature settings for
auxiliary functions
Depending on the step the programme has reached, you
may cancel or activate the auxiliary functions; see, "Auxiliary
function selection".
You may also change the speed and temperature settings;
see, "Spin speed selection" and "Temperature selection".
C
If no change is allowed, the relevant light will flash for
3 times.
4.15 Adding or taking out laundry
Press the Start / Pause button to switch the machine to
pause mode. The programme follow-up light of the relevant
step during which the machine was switched into the pause
mode will flash. Wait until the Loading Door can be opened.
Open the Loading Door and add or take out the laundry.
Close the Loading Door. Make changes in auxiliary functions,
temperature and speed settings if necessary. Press Start /
Pause button to start the machine.
4.16 canceling the programme
To cancel the programme, turn the Programme Selection
knob to select another programme. Previous programme
will be canceled. End / Cancel light will flash continuously to
notify that the programme has been canceled.
Your machine will end the programme when you turn the
Programme Selection knob; however, it does not drain the
water inside. When you select and start a new programme,
the newly selected programme will start depending on the
step the previous programme was canceled in. For example,
it may take in additional water or continue to wash with the
water inside.
C
Depending on the step where the programme was
canceled in, you may have to put detergent and softener
again for the programme you have selected anew.
Washing Machine / User's Manual