Inhaltsverzeichnis
Werbung
GB
•
The tool does not work
•
when switched on.
D
•
NL
•
When cutting it is very
•
difficult to move the
F
work forward in a
straight line and the cut
E
is not clean.
•
The circular saw
•
P
makes a lot of noise
and/or does not run
smoothly.
I
Cleaning
Keep the ventilation slots of the machine clean to prevent overheating of the engine.
S
Regularly clean the machine housing with a soft cloth, preferably after each use. Keep the
ventilation slots free from dust and dirt.
If the dirt does not come off use a soft cloth moistened with soapy water. Never use sol-
SF
vents such as petrol, alcohol, ammonia water, etc. These solvents may damage the
plastic parts.
N
Replacing hte carbon brushes
Fig. F
DK
•
Remove the screws (17).
•
Withdraw the carbon brushes (18) from the circular handsaw and inspect them for
wear.
•
Place the carbon brushes back in the brush holders provided.
•
Check that the copper contact on the carbon brushes makes good contact with the
copper part in the brush holder.
•
Replace the screws (17) and tighten them firmly.
Frequent use will cause the carbon brushes to wear down. Regular inspection,
after every 30 hours of use, is essential. If the brushes have worn down to less
than 4 mm, replace.
Lubrication
The machine requires no additional lubrication.
Faults
Should a fault occur, e.g. after wear of a part, please contact the service address on the
warranty card. In the back of this manual you find an exploded view showing the parts
that can be ordered.
12
Damaged cord and/or
•
Check cord and/or
plug.
plug.
Defective switch.
•
Please contact the
service address on the
warranty card.
The blade is bent or
•
Replace the blade.
blunt.
The carbon brushes
•
Please contact the
are worn.
service address on the
warranty card.
RUNDSAV
Tallende i den følgende tekst korresponderer med afbildningerne på side 2 - 4.
Læs denne brugsanvisning godt igennem før maskinen tages i brug. Sørg for
at De kender maskinens funktion og betjening. Vedligehold maskinen i følge
instruktionerne, for at maskinen altid kan fungere optimalt. Bevar denne brug-
sanvisning og den vedlagte dokumentation til maskinen.
Indhold
1.
Tekniske specifikationer
2.
Sikkerhedsforskrifter
3.
Montage og indstillings forskrifter
4.
Betjening
5.
Vedligeholdelse
1. TEKNISKE SPECIFIKATIONER
Tekniske data
Spænding
Frekvens
Optaget effekt
Omdrejninger, ubelastet
Savklinge
Tænder
Maksimal savdybde 90°
Maksimal savdybde 45°
IP-klasse
Vægt
Lpa (lydtryk)
Lwa (lydeffekt)
Vibrationsværdi
Produktinformation
Fig. A
1.
Håndtag
2.
Tænd/sluk-kontakt
3.
Spændeknap til skæredybde
4.
Netledning
5.
Sikkerhedsskærm til savklinge
6.
Sekskantskrue
7.
Bundplade
8.
Stopring
9.
Savklinge
10. Kløveanlægsflade
Ferm
Ferm
DK
D
NL
F
E
P
I
S
230 V~
SF
50 Hz
1200 W
5000/min.
∅185 x ∅20 x 2.4 mm
N
Z24
65 mm
DK
43 mm
IP 20
4.05 kg
92.3 dB(A)
103.3 dB(A)
4.689 m/s
2
93
Werbung
Kapitel
Inhaltsverzeichnis
