CAUTION: OVERlOAD:
•
If you use extension leads, these should have a cable
cross-section of at least 1.5 mm
•
Do not use any multiple sockets, as this device is too
powerful.
NOTE: Always use fresh water.
1. Place the machine on a flat surface.
2. Press the button in the lead in order to open the kettle. Then
fill in the water. Please only fill up to the maximum (MAX)
mark. You can read the filling level on the water level indica-
tor of the
kettle.
3. Close the lid until you hear it lock in place.
4. Place the kettle flush on the base.
5. Only connect the machine to a properly installed 230 V,
50 Hz safety socket.
6. Switch on the kettle by pressing the switch. To control lamp
lights up.
7. After boiling has finished the kettle switches off automati-
cally, or you can push the switch upwards to interrupt or stop
the boiling process.
WARNING: Danger of scalding!
•
When pouring the water out, keep the lid closed.
•
During operation the housing becomes hot. Do not touch it
and allow the device to cool down before storing it away.
Switching off
•
If you would like to turn the kettle off, push the switch
upwards and remove the plug from the socket.
•
The control lamp goes off.
•
Emptying the water container.
Mains Cable Take-up Device
The mains cable can be wound up on the base.
WARNING:
•
Always turn the device off before cleaning it and remove
the mains plug. Wait until the device has cooled down.
•
Never immerse the device or the base in water or other
liquids.
CAUTION:
•
Do not use any wire brush or other abrasive objects.
•
Do not use any acidic or abrasive detergents.
•
Rinse the water container out with clean water. Then dry it
off with a cloth.
•
Clean the housing after use with a slightly damp cloth.
22
05-WK 5005 G CB Neu.indd 22
.
2
Use
Cleaning
filter
There is a permanent filter in the spout. In order to clean the
filter, remove it from the movable frame.
•
Pull the right-hand tab inside the kettle.
•
Remove the filter.
•
Rinse out the filter with running water. You can use a nylon
brush.
•
Put the filter back in position: insert first of all the axle into
the left-hand guide groove of the frame. Then press the filter
into the frame. It must be heard to click into place.
NOTE:
The filter is correctly inserted if it can be moved together with
the frame.
Decalcification
•
The frequency of the decalcifying operation depends on the
hardness of the water and on how often the appliance is
used.
•
If the machine switches off before the water boils, it probably
needs to be decalcified.
•
Please do not use vinegar but a commercially available
decalcification agent on the basis of citric acid. Only use the
quantities stated in the instructions.
NOTE:
After descaling the device boil fresh water in it several times
(approximately 3-4 times) in order to remove any residues. Do
not consume this water.
Troubleshooting
•
It is not possible to switch the machine on.
Possible Cause:
After being used without or with too little water the machine
has not cooled down sufficiently.
Remedy:
Allow the machine to cool down for 15 min.
•
The machine switches off before the water has boiled.
Possible Cause:
The heated base is coated with too much lime or the circuit
of the plug is overloaded.
Remedy:
Descale the machine as instructed.
Check the mains connection.
•
The machine does not switch off.
Possible Cause:
The lid is not closed or the filter is not inserted.
Remedy:
Close the lid until it locks in place or re-insert the filter.
12.10.2010 11:16:11 Uhr
M
P
P
P
F
N
T
C
v
t
S
P
i
P
u
T
e
T
t
I
c