Denon DN-X100 Bedienungsanleitung Seite 6

ENGLISH
!4
Crossfader
• Fades the overall mixer output between
channels 1 and 2.
!5
Level Meter
• The dual LED's indicators are used to detail
either the master output level, a combination of
the master output level and the CUE signal
level, or the PGM1/2 monaural level.
!6
CH REVERSE button
• This switch allows the left hand fader or right
hand fader to control PGM1 or PGM2.
• When the CH REVERSE mode is ON, the CH1
fader will be able to control PGM 2 sound and
the CH2 fader will be able to control PGM 1
sound..
NOTE:
• Please don't confuse with the CH 1/2 FADER
REVERSE switch (#2 ) .
!7
Level meter mode select switch
• The position of this switch will determine the
Level Meter mode. In the "MASTER" position,
the meter will detail the out level of the left and
right channels. In the "PGM 1/2" position, the
left side of the meter will indicate monaural
level of the PGM 1 and the right side of the
meter will indicate monaural level of the PGM 2.
6
(2) Rear panel
!8
Power operation switch (POWER)
• Selects power "ON" or "OFF".
NOTE:
Whenever the power switch is in the OFF state,
the AC adaptor is still connected on AC line
voltage. Please be sure to unplug the cord when
you don't use for along time.
!9
Balanced MASTER OUT jacks (BAL.)
• These 1/4" TRS jacks provide a balanced line
level output.
• Connect these jacks to the balanced analog
input jacks on an amplifier or console.
• Pin layout: Tip=Hot Ring=Cold Sleeve=GND
@0
MIC BALANCED INPUT jack
• Accepts an balanced microphone with 1/4" TRS
mono jacks.
• Pin layout: Tip=Hot Ring=Cold Sleeve=GND
@1
PGM1, 2 FADER output jacks
• Connect these jacks to the FADER input jacks of
DN-S3000, DN-S5000, DN-S1000 and etc. using
the 3.5mm stereo mini cord.
@2
Phono ground screw (GND)
• This screws provide a place to connect the
ground wire from a turntable.
• This terminal is exclusively for a turntable
ground and not a safety earth ground.
@3
PHONO1, 2 / LINE1, 3 switches
(LN / PH)
• These switches change the input from PHONO
to a LINE level input.
• These switches set a LINE level input when
turntable is not connected.
NOTE:
Always be sure main power is shut off before
change the position of the Line Level Selector
Switch.
@4
PHONO1, 2 / LINE1, 3 input jacks
• These stereo pair of unbalanced RCA jacks are
inputs for a PHONO (RIAA) stage for magnetic
(MM) cartridges or a LINE stage suitable for any
device, such as a CD player.
@5
LINE2, 4 input jacks
• These stereo pair of unbalanced RCA jacks are
inputs for any line level device.
@6
Unbalanced MASTER OUT jacks
• This stereo pair of RCA jacks provides an
unbalanced line level output.
• Connect these jacks to the unbalanced analog
input jacks on an amplifier or console.
@7
AC IN
• Input connection for the included AC adaptor.
NOTE:
Use specified attached AC adaptor only.
(3) Front panel
@8
CH 1/2 FADER START switches
• Use this to switch the Channel Fader Start
function ON and OFF.
@9
CROSSFADER START A/B switches
• Use this to switch the Crossader Start function
ON and OFF.
#0
HEADPHONE output jack
• Accept 1/4" stereo headphone plugs.
#1
CH 1/2 FADER CONTOUR adjustment
• Adjusts the curve of the CH1/2 faders between
fast, normal , or slow fade.
#2
CH 1/2 FADER REVERSE switch
• Reverses the direction of each respective input
CH1/2 fader.
#3
CROSSFADER CONTOUR adjustment
• Adjusts the shape of the crossfader curve from
a fast cut for scratching or to a slow fade for
mixing.
#4
CROSSFADER REVERSE switch
• Reverses the direction of the crossfader.