Pioneer DEQ-P6600 Installationsanleitung

DEQ-P6600
This product conforms to new cord colors.
Los colores de los cables de este producto se confor-
man con un nuevo código de colores.
Dieses Produkt entspricht den neuen Kabelfarben.
Le code de couleur des câbles utilisé pour ce produit
est nouveau.
Questo prodotto è conforme ai nuovi codici colori.
De kleuren van de snoeren van dit toestel zijn gewijzigd.
Printed in Japan
Imprimé au Japon
<CRD3876-A> EW <KSNNF> <04D00000>
1
9
2
10
4
3 6
5
Fig. 1 Fig. 3
Abb. 1 Abb. 3
Afb. 1 Afb. 3
7
11
8
12
Fig. 2 Fig. 4
Abb. 2 Abb. 4
Afb. 2 Afb. 4
Installation <ENGLISH>
Note: Routing the optical cable
• Before finally installing the unit, connect the
wiring temporarily, making sure it is all connect-
Precaution:
ed up properly, and the unit and the system work
• Try not to bend the optical cable sharply. If it is
properly.
necessary to bend it sharply, make sure that the
• Use only the parts included with the unit to
bending radius is at least 25 mm, otherwise the
ensure proper installation. The use of unautho-
cable will not transfer signals properly and so
rized parts can cause malfunctions.
this unit will not work properly.
• Consult with your nearest dealer if installation
• Route the optical cable so that nothing heavy
requires the drilling of holes or other modifica-
rests on it, and so that it cannot be stepped on or
tions of the vehicle.
caught in anything – for instance, a door.
• Install the unit where it does not get in the dri-
• Make a loop of diameter at least 200 mm with
ver's way and cannot injure the passenger if there
the remaining optical cable so that the cable does
is a sudden stop, like an emergency stop.
not get strained.
• When mounting this unit, make sure none of the
• When plugging the optical cable into the unit,
leads are trapped between this unit and the sur-
use the supplied cable clamps to prevent the
rounding metalwork or fittings.
cable from being bent sharply.
• Do not mount this unit near the heater outlet,
• Route the optical cable so that it does not get
where it would be affected by heat, or near the
caught in moving parts such as the gear shift,
doors, where rainwater might splash onto it.
hand brake, or seat sliding mechanism. Keep the
• Before drilling any mounting holes always check
cable away from hot spots, such as near the
behind where you want to drill the holes. Do not
heater outlet.
drill into the gas line, brake line, electrical wiring
or other important parts.
Using the corrugated tube (Fig. 3)
• If this unit is installed in the passenger compart-
To prevent the optical cable from being strained,
ment, anchor it securely so it does not break free
use the corrugated tube after cutting it to the cor-
while the car is moving, and cause injury or an
rect length.
accident.
• If this unit is installed under a front seat, make
• Insert the optical cable into the cor-
sure it does not obstruct seat movement. Route
rugated tube.
all leads and cords carefully around the sliding
mechanism so they do not get caught or pinched 9. Optical cable
in the mechanism and cause a short circuit.
10. Corrugated tube
Mounting the clamp (Fig. 4)
Installing the unit
The clamp is used to secure the optical cable
when using it. The other clamp is installed on the
Mounting with brackets (Fig. 1)
back side of the head unit similarly and used to
1. Tapping screw (4 × 12 mm) secure the optical cable.
2. Screw (4 × 8 mm)
1. Insert the clamp in the direction
3. Bracket
indicated in the figure, and turn it 90
4. Do not close this area.
5. Drill 2 to 2.5 mm diameter holes. degrees to lock.
6. Car mat or chassis
11. Clamp
Mounting with velcro tape (Fig. 2)
2. Secure the optical cable.
Thoroughly wipe off the surface before affixing
12. Optical cable
the velcro tape.
7. Velcro tape
8. Car mat or chassis
Connecting the Units <ENGLISH>
Note:
• This unit is for vehicles with a 12-volt battery • When an external power amp is being used with
and negative grounding. Before installing it in a this system, be sure not to connect the blue/white
recreational vehicle, truck, or bus, check the bat- lead to the amp's power terminal. Likewise, do
tery voltage. not connect the blue/white lead to the power ter-
minal of the auto-antenna. Such connection could
• To avoid shorts in the electrical system, be sure
to disconnect the · battery cable before begin- cause excessive current drain and malfunction.
ning installation. • To avoid short-circuiting, cover the disconnected
lead with insulating tape. Especially, insulate the
• Refer to the owner's manual for details on con-
unused speaker leads without fail. There is a pos-
necting the power amp and other units, then
sibility of short-circuiting if the leads are not
make connections correctly.
insulated.
• Secure the wiring with cable clamps or adhesive
• To prevent incorrect connection, the input side of
tape. To protect the wiring, wrap adhesive tape
the IP-BUS or optical cable connector is blue,
around them where they lie against metal parts.
and the output side is black. Connect the connec-
• Route and secure all wiring so it cannot touch
tors of the same colors correctly.
any moving parts, such as the gear shift, hand-
• If this unit is installed in a vehicle that does not
brake and seat rails. Do not route wiring in
have an ACC (accessory) position on the ignition
places that get hot, such as near the heater outlet.
switch, the red lead of the unit should be con-
If the insulation of the wiring melts or gets torn,
there is a danger of the wiring short-circuiting to nected to a terminal coupled with ignition switch
the vehicle body. ON/OFF operations. If this is not done, the vehi-
cle battery may be drained when you are away
• Don't pass the yellow lead through a hole into
from the vehicle for several hours.
the engine compartment to connect to the battery.
This will damage the lead insulation and cause a
very dangerous short.
• Do not shorten any leads. If you do, the protec-
tion circuit may fail to work when it should.
• Never feed power to other equipment by cutting
the insulation of the power supply lead of the
unit and tapping into the lead. The current capac-
ACC position No ACC position
ity of the lead will be exceeded, causing over-
heating.
• When replacing fuse, be sure to use only fuse of
• The black lead is ground. Please ground this lead
the rating prescribed on the fuse holder.
separately from the ground of high-current prod-
• Since a unique BPTL circuit is employed, never ucts such as power amps.
wire so the speaker leads are directly grounded or If you ground the products together and the
the left and right · speaker leads are common.
ground becomes detached, there is a risk of dam-
• Speakers connected to this unit must be high- age to the products or fire.
power types with minimum rating of 50 W and • To ensure proper heat dissipation of this product,
impedance of 4 to 8 ohms. Connecting speakers
take special care not to block the cooling fan side
with output and/or impedance values other than
of this product.
those noted here may result in the speakers catch-
ing fire, emitting smoke or becoming damaged.
• Cords for this product and those for other prod-
• When this product's source is switched ON, a
ucts may be different colors even if they have
control signal is output through the blue/white
the same function. When connecting this prod-
lead. Connect to an external power amp's system
uct to another product, refer to the supplied
remote control or the car's Auto-antenna relay
manuals of both products and connect cords that
control terminal (max. 300 mA 12 V DC). If the
have the same function.
car features a glass antenna, connect to the anten-
na booster power supply terminal.