Specifications - Panasonic EY6220 Betriebsanleitung

P05-11(EY6220EN).qxd 10.7.22 14:12 ページ 10
B536502_EY6220_Tori_EU

SPECIFICATIONS

CORDLESS DRILL & DRIVER (EY6220)
Motor DC Motor 2.4 V
LOW: 200 min
No load speed
HIGH: 400 min
Hexagonal driving shaft 6.35 mm, (1/4") across flats
Maximum drilling dia. for metal 2 mm (5/64")
LOW: 2.9 Nm (30 kg-cm, 26 in.lbs)
Maximum torque
HIGH: 1.5 Nm (15 kg-cm, 13 in.lbs)
Maximum clutch torque 2.0 Nm (20 kg-cm, 17.5 in.lbs) at 5 position
Overall length 239 mm (9-3/8")
Weight (with battery pack) 0.4 kg (0.9 lbs)
BATTERY PACK (EY9221)
Storage battery Ni-MH battery
Battery voltage 2.4 V DC (1.2 V × 2 cells)
BATTERY CHARGER (EY0L11)
Charging time 45 min
Mass (Weight) 0.6 kg (1.54 lbs)
NOTE: For applicable battery packs to this charger, see the label on the charger or the latest general
catalog.
Refine_EY6220.10.p1.pdf
Refine_10-08-18 10:30:43
(rpm)
-1
(rpm)
-1
10
P05-11(EY6220EN).qxd 10.5.31 17:02 ページ 11
6 10-08-23 15:56:41
ONLY FOR U.K.
ELECTRICAL PLUG
INFORMATION
F O R Y O U R S A F E T Y P L E A S E R E A D T H E
F O L L O W I N G T E X T C A R E F U L L Y
This appliance is supplied with a moulded
three pin mains plug for your safety and
convenience.
A 3 amp fuse is fitted in this plug.
Should the fuse need to be replaced please
ensure that the replacement fuse has a
rating of 3 amp and that it is approved by
ASTA or BSI to BS1362.
Check for the ASTA mark 7 or the BSI
mark 6 on the body of the fuse.
If the plug contains a removable fuse cover
you must ensure that it is refitted when the
fuse is replaced.
If you lose the fuse cover the plug must not
be used until a replacement cover is
obtained.
A replacement fuse cover can be purchased
from your local Panasonic Dealer.
IF THE FITTED MOULDED PLUG
UNSUITABLE FOR THE SOCKET OUTLET
IN YOUR HOME THEN THE FUSE
SHOULD BE REMOVED AND THE PLUG
CUT OFF AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE
ELECTRICAL SHOCK IF THE CUT OFF
PLUG IS INSERTED INTO ANY 13 AMP
SOCKET.
If a new plug is to be fitted please observe
the wiring code as shown below.
If in any doubt please consult a qualified
electrician.
Refine_EY6220.11.p1.pdf
Refine_10-08-18 10:30:44
IMPORTANT: The wires in this mains lead
are coloured in accordance
with the following code:
Blue: Neutral
Brown: Live
As the colours of the wire in the mains lead
of this appliance may not correspond with
the coloured markings identifying the
terminals in your plug, proceed as follows.
The wire which is coloured BLUE must be
connected to the terminal in the plug which
is marked with the letter N or coloured
BLACK.
The wire which is coloured BROWN must be
connected to the terminal in the plug which
is marked with the letter L or coloured RED.
Under no circumstances should either of
these wires be connected to the earth
terminal of the three pin plug, marked with
the letter E or the Earth Symbol L .
How to replace the fuse: Open the fuse
compartment with a screwdriver and replace
the fuse and fuse cover if it is removable.
IS
Fuse Cover
This apparatus was produced to BS800.
11