Condensation; If Problem Occurs; Factory Reset, Clearing All Memory; Before Transporting The Unit - Pioneer X-HM70-S Bedienungsanleitung

Additional Information
not, set the SSID, etc., by making the wireless LAN converter
settings on the receiver manually.
 The access point's security settings use WEP 152-bit length
code key or shared key authentication. The receiver does not
support WEP 152-bit length code key or shared key
authentication.
 Network connections cannot be established even when the
above measures are taken. Reset the wireless LAN converter.
After this, redo the wireless LAN converter's settings.
- About resetting
1. Check that the wireless LAN converter's power is on.
2. Press the wireless LAN converter's reset button for at least
3 seconds.
3. Release the reset button.
When the wireless LAN converter is restarted, the resetting
procedure is completed.

Condensation

Sudden temperature changes, storage or operation in an
extremely humid environment may cause condensation
inside the cabinet (CD pickup, etc.) or on the transmitter on
the remote control. Condensation can cause the unit to
malfunction. If this happens, leave the power on with no disc
in the unit until normal playback is possible (about 1 hour).
Wipe off any condensation on the transmitter with a soft
cloth before operating the unit.

If problem occurs

When this product is subjected to strong external
interference (mechanical shock, excessive static electricity,
abnormal supply voltage due to lightning, etc.) or if it is
operated incorrectly, it may malfunction.
If such a problem occurs, do the following:
1 Set the unit to the stand-by mode and turn the power
on again.
2 If the unit is not restored in the previous operation,
unplug and plug in the unit again, and then turn the
power on.
Note
• If neither operation above restores the unit, clear all the
memory by resetting it.

Factory reset, clearing all memory

If iPod or iPhone is connected to the unit, disconnect it.
1 Press the STANDBY/ON button to enter the power
stand-by mode.
2 Press both STANDBY/ON button and
unit.
'RESET YES?' appears.
3 Press / ( ) button.
'RESET...' appears.
If you don't press / ( ) button within 10 minutes after
STEP 2, RESET MODE is canceled.
CAUTION
• This operation will erase all data stored in memory
including clock, timer settings, tuner preset, and CD
programme.

Before transporting the unit

Remove the iPod, USB memory device and disc from the
unit. Then, set the unit to the power stand-by mode. Carrying
the unit with iPod or USB memory device left docked or discs
left inside might damage the unit.

Care of compact discs

Compact discs are fairly resistant to damage, however
mistracking can occur due to an accumulation of dirt on the
disc surface. Follow the guidelines below for maximum
enjoyment from your CD collection and player.
• Do not write on either side of the disc, particularly the
non-label side from which signals are read. Do not mark
this surface.
• Keep your discs away from direct sunlight, heat, and
excessive moisture.
• Always hold the CDs by the edges. Fingerprints, dirt, or
water on the CDs can cause noise or mistracking. If a CD
is dirty or does not play properly, clean it with a soft, dry
cloth, wiping straight out from the centre, along the
radius.
button on the NO

Cleaning the cabinet

Periodically wipe the cabinet with a soft cloth and a diluted
soap solution, then with a dry cloth.
CAUTION
• Do not use chemicals for cleaning (petrol, paint thinner,
etc.). It may damage the cabinet.
• Do not apply oil to the inside of the unit. It may cause
malfunctions.
Caution for when the unit is installed in a rack
with a glass door
OPEN/CLOSE on the remote control to
Do not press the
open the disc tray while the glass door is closed. The door will
hamper the movement of the disc tray, and the unit could be
damaged.
YES
Correct
29
En