Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Tips
•
If you need to take a break during vacuum
cleaning, you can slide the floor nozzle into
the storage bracket (18) on the back of the
appliance.
•
The small crevice and brush nozzle (13)
can be used with and without brushes, as
they can easily be extended or withdrawn.
The nozzle can be stored in the storage
space on the back of the appliance when it
is not in use.
•
You can lift and carry the appliance using
the carrying handle (1). Never pull or lift the
appliance by the cord.
REPLACING THE DUST BAG
If the bag change indicator indicates that the
bag is full or if the suction force is significantly
reduced, this may mean that the dust bag
needs replacing. Never use the appliance if the
bag is full or with no bag at all.
1.
Turn off the appliance.
2.
Detach the hose.
3.
Open the lid by pressing the button
underneath the edge of the lid and lifting
the lid until it locks into place.
4.
Remove the dust bag.
5.
Place the bag carefully in a refuse bin.
Make sure that there are no holes in it.
Avoid bending or squeezing the bag.
6.
Place a new dust bag in the appliance.
Check that the bag is secure and facing in
the right direction.
7.
Close the lid and ensure it clicks into place.
REPLACING THE MOTOR FILTER
The motor filter is the filter behind the dust
bag. The appliance must not be used without a
motor filter.
1.
Turn off the appliance.
2.
Detach the hose.
3.
Open the lid by pressing the button
underneath the edge of the lid and lifting
the lid until it locks into place.
4.
Remove the dust bag from the appliance.
5.
Remove the motor filter from the holder and
replace the filter or clean it as described in
the section on cleaning below.
6.
Replace the motor filter in the holder.
7.
Check the dust bag is correctly fitted onto
the rails before closing the lid.
We recommend cleaning the filter at least twice
a year, or whenever it is dirty.
REPLACING THE EXHAUST FILTER
The exhaust filter is used to filter exhaust air
from the appliance. The appliance must not be
used without an exhaust filter.
•
Remove the exhaust grille (16) on the side
of the appliance by pressing the release
button on the grille.
•
Remove the exhaust filter from the back
of the grille and replace the filter or clean
it as described in the section on cleaning
below.
•
Replace the exhaust filter on the back of
the grille.
•
Fit the exhaust grille and ensure it clicks
into place.
We recommend replacing the exhaust filter after
4 to 6 months' use, when it becomes soiled, or
if the vacuum cleaner's suction force is reduced.
STORAGE
•
Before putting the appliance away, rewind
the cord. Switch off at the mains, remove
the plug and press the automatic cord
rewind button on the left side of the
carrying handle until the cord is completely
rewound. Hold the plug during rewinding
to prevent it from hitting the appliance as
this could damage either the appliance or
the plug.
•
The floor nozzle can be stored in the
storage bracket at the rear end of the
appliance.
•
Store the appliance in a clean and dry
place.
•
Do not place heavy objects on top of the
appliance.
CLEANING
When cleaning the appliance, you should pay
attention to the following:
•
Unplug the appliance before cleaning it.
•
Never submerge the appliance in water and
make sure no water enters the appliance.
•
Clean the appliance by wiping it with a
damp cloth. A little detergent can be added
if the appliance is heavily soiled.
•
Do not use scouring pads, steel wool or
any form of strong solvents or abrasive
cleaning agents to clean the appliance, as
they may damage the external surfaces of
the appliance.
•
IMPORTANT! Allow to dry completely after
cleaning. Do not use the appliance if it is
damp.
20
Werbung
Inhaltsverzeichnis
