Noise/Vibration Information; Declaration Of Conformity - Bosch GBM 1600 RE Professional Originalbetriebsanleitung

OBJ_BUCH-2420-002.book Page 13 Thursday, April 16, 2015 11:27 AM
Rotary drill
Spindle collar dia.
Max. drilling dia.
– Steel
– Wood
– Aluminium
Chuck clamping range
Right/left rotation
Maximum stirrer paddle diameter
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.

Noise/Vibration Information

Sound emission values determined according to
EN 60745-2-1.
Typically the A-weighted noise levels of the product are:
Sound pressure level 85 dB(A); Sound power level 96 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-1:
2
Drilling into metal: a <2.5 m/s , K=1.5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards: EN 60745-1,
EN 60745-2-1.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Bosch Power Tools
Henk Becker
GBM 1600 RE
Executive Vice President
mm 43
Engineering
mm 16
mm 40
mm 16
mm 3 – 16
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY

Leinfelden, 16.04.2015
mm 160
Assembly
kg 3.0
 Before any work on the machine itself, pull the mains
/II
plug.
Auxiliary handles (see figure A)
 Operate your machine only with the auxiliary handles 2
and 4.
Screw the auxiliary handle 2 into the thread 3 on the motor
housing.
The auxiliary handle 4 can be rotated through 360°.
Changing the Tool (see figure B)
 Wear protective gloves when changing the tool. The
drill chuck can become very hot during longer work peri-
ods.
2
.
Open the key type drill chuck 1 by turning until the tool can be
inserted. Insert the tool.
Insert the chuck key 9 into the corresponding holes of the key
type drill chuck 1 and clamp the tool uniformly.
Replacing the Drill Chuck (see figure C)
Removing the Securing Screw
The key type drill chuck 1 is secured with a securing screw 10
against unintentional loosening. Open the drill chuck 1 com-
pletely and unscrew the securing screw 10 by turning in
clockwise direction. Please observe that the securing
screw has a left-hand thread.
If the securing screw 10 is seated tightly, apply a screwdriver
to the screw head and loosen the securing screw by giving a
blow onto the handle of the screwdriver.
Removing the Drill Chuck
To dismount the key type drill chuck 1 position an open-end
spanner (size 17 mm) against the nut on the drive spindle.
Firmly hold the key type drill chuck with one hand and with the
other hand, turn the open-end spanner in anticlockwise direc-
tion until the drill chuck is released from the tapered drill spin-
dle.
Mounting the Drill Chuck
 Keep the drill spindle taper and the drill hole of the drill
chuck free from grease and debris.
To mount the key type drill chuck 1 turn the nut on the drive
spindle in clockwise direction to the stop. Place the key type
drill chuck without force onto the drive spindle until it is tightly
seated. Apply light blows with a rubber hammer onto the face
English | 13
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
1 609 92A 1CD | (16.4.15)