3 // How to mount the light and battery?
4 // Adjust the lightlevels
The dimmlevels and a couple of other useful functions can be adjusted. Keep the
Helmetlight Neo:
button pressed and wait till the main light blinks up once a second.
First attach the thin velcro with the Lupine logo to the helmetmount (see
If you release the button, the particular program as shown below is chosen.
Fig. 1), then pull the other end of the velcro through the ventilation ope-
nings available on your helmet and fix it on the other side of the helmet
mount.
Dim levels:
Explanation:
Direct the light into a straight forward position and tighten the velcro to
avoid slipping of the lighthead during use (see Fig. 2).
1
0.3W + 10W
35 + 900 Lumens
2
0.3W + 5W + 10W
35 + 530 + 900 Lumens
With the provided extension, the battery may be carried in your jersey or
backpack. The flexible velcro strap allows to put the battery directly on the
3
0.3W + 1.5W + 5W + 10W
35 + 170 + 530 + 900 Lumens
helmet (see Fig. 3).
4
Red + 0.3W + 5W + 10W
Low redlight, in combination with the diffu-
sor. Good for reading maps.
5
Red + 0.3W + 5W
Headlight Neo:
6
Low Start on
The light starts on lowest beam
Thanks to the battery FastClick-System you can carry all Lupine FastClick
batteries directly on the headband (see Fig. 4).
7
Low Start off
The light starts on high beam
8
Battery high
Warning & Reservepower activated early
More Options:
9
Battery low
Warning & Reservepower activated later
GoPro mount (Art.No. 1070) for the helmet and
Quickrelease mount (Art.No. 225 and 231) for the handlebar.
10
Alpine SOS
Blinks till battery is empty or button pushed
* To change the lamphead from one mount to another, you have to open
11
SOS
Blinks till battery is empty or button pushed
the two screws on the lamphead with an 3mm allen key.
www.lupine.de
5 // Additional functions
6 // Smartcore Batteries
Capacity Indicator
Capacity Indicator
Voltage test:
Audible:
Audible:
After connecting the lamphead to the battery, the upper and lower red LEDs
To check the capacity, simply press the touch-pad once. At rst an audible signal
To check the capacity, simply press the touch-pad once. At rst an audible signal
will blink to indicate the battery voltage. The voltage helps to interpret the
will sound, which is especially useful while using the battery mounted on a hel-
will sound, which is especially useful while using the battery mounted on a hel-
remaining capacity.
met or headband, to give a quick reading in 20% steps.
met or headband, to give a quick reading in 20% steps.
For example:
Factory settings
7x upper red LEDs
Visible:
Visible:
Upper red LEDs blinks: 1 time each volt
+
3x lower red LEDs
Lower red LEDs blinks: 1 time each 1/10 volt
The visible indicator uses 5 red LEDs. The LEDs can operate in two di erent
The visible indicator uses 5 red LEDs. The LEDs can operate in two di erent
=
7.3V
operating states: blinking and continuous. LED meanings: A blinking LED
operating states: blinking and continuous. LED meanings:
Hints:
is indicating a 10% step and a continuously glowing LED a 20% step.
is indicating a 10% step and a continuously glowing LED a 20% step.
More than 8V = battery fully charged
7.1 to 7.9V = recharge
Example:
Example:
Example:
Example:
3 LEDs steady glow (20 %, 40 %, 60 %) + 1 LED blinking (80 %) = 70% Capacity
3 LEDs
Below 7V = not or only partly ready for use
Low battery warning:
Taillight
Taillight
Once the remaining capacity dropped by a relevant amount, the lampheads red
To run the taillight simply press the touch pad two times and the 5 LEDs will
To run the taillight simply
LEDs will turn on. If the battery is empty, the lamphead itself will start to flash a
operate continuously. To switch o the taillight, simply press the pad again.
operate continuously. To switch o the taillight, simply press the pad again.
couple of times. Stop immediately! The light will switch off by itself.
Reservepower:
Moving light:
Moving light:
After switching the light on again, reserve power is available for a short while.
Press the touch pad three times to activate the moving light. To switch it o
Press the touch pad three times
Slow down since the light will be switched off automatically.
press the button another time.
press the button another time.
Important: charge the battery in a short while. Deep discharging will harm the battery.
An activated reservepower will be shown by the red LEDs flashing.
www.lupine.de
www.lupine.de
Letzte Hinweise / Miscellaneous
Regelungen/Regulations:
Die Verwendung dieses Beleuchtungssystems für bestimmte Zwecke kann in
Europa von Land zu Land unterschiedlich geregelt sein. Informieren Sie sich über
die in Ihrem Land gültigen Bestimmungen.
The laws governing the allowable application domain for this lighting system
may vary from one country to another. We recommend that you inform
yourself about the relevant laws in this domain in your country.
A blinking LED
Änderungen/ Changes:
Weiterentwicklungen der Produkte und technische Änderungen vorbehalten.
steady glow
(20 %, 40 %, 60 %) + 1 LED
blinking
(80 %) = 70% Capacity
Rights for improvements and modifications of our products reserved.
Garantie/Warranty:
press the touch pad two times
and the 5 LEDs will
Innerhalb der Garantiezeit von 24 Monaten umfasst die Gewährleistung alle
Komponenten und deckt fertigungsbedingte Mängel ab. Ausgenommen ist
jedoch der Akku. Des Weiteren erlöschen die Garantieansprüche bei nicht be-
stimmungsgemäßer Benutzung oder Veränderungen jeglicher Art.
to activate the moving light. To switch it o
The product's two year warranty applies to all components, as well as any ma-
nufacturing defect. The warranty does not include the battery, however. In ad-
dition, any modification or improper use of the product will void the warranty.
www.lupine.de
www.lupine.de
Technical Data:
Power:
Lumens:
Runtime
Runtime
Neo X2
Neo 4 / X4
10W
900
1:30h
2:15h
5W
530
3 h
4:30h
1.5W
170
9:30h
16h
0.3W
35
48h
80h
Red LEDs
-
48h
80h
Abb.3
Fig.3
Abb.1
Weight:
Protection Class: IP68
Fig.1
Neo Lamphead:
50g
Operating temperature: -25°C to +70°C
Neo X2:
175g
Abb.4
Abb.4
Neo X2 Smartcore:
175g
Neo X4 Smartcore:
195g
Wiesel Charger:
Fig.4
Fig.4
Neo 4:
175g
Input Voltage: 100 – 240V~, 50-60Hz
Neo 4 Smartcore:
175g
Charging current: 1.2A
Abb.2
Fig.2
Register your Neo:
Battery:
register.lupine.de
2.0 Ah / 7.2V Li-Ion
3.3 Ah / 7.2V Li-Ion
Mehr Informationen unter www.lupine.de
EG-Konformitätserklärung: www.lupine.de/ce/
More informations at www.lupine.de
EC Declaration of Conformity: www.lupine.de/ce/
www.lupine.de
www.lupine.de
LIGHTING SYSTEMS
Factory settings
*Runtime varies
according to the
battery age,
condition, as well
the ambient
temperature.
Bedienungsanleitung / User Manual