Assembly Instructions; Operation Instructions; Maintenance And Service - Pattfield PA-550ST Bedienungsanleitung

IV - Assembly instructions
1 Attaching the blade
WARNING! To prevent personal injury,
always disconnect plug from power
source before assembling parts, making
adjustments, or changing blades.
1. Only use saw blades with a T-shank.
2. Insert the hexagonal key(13) into the hole
in the key type chuck key(10). Loosen the
key type chuck (10) by turning the hexagonal
key in anti-clockwise direction. Then insert
required saw blade (12) and fasten the key
type chuck (10) by turning the hexagonal key
GB
3. The saw blade (12) must be in the guide
roller (8).
Fig.1
97
2 Dust extraction
Your jig saw is equipped with a dust port for
dust and chip extraction.
Please insert the dust port into the back of
the machine where connect the dust port (4)
and turn the dust port until both tubers slip
dust port please turn it until two tubers leave
V - Operation instructions
1 Intended use
This tool is suitable for making straight and
curved cuts and miter cuts on squared work
pieces made of plastic, wood and metal. The
tool is approved solely for private use in dry
areas. Please observe the notes relating
to the types of saw blade. Any other use or
use and poses a serious risk of accident.
The manufacturer is not liable for damage
caused by improper use of the tool.
2 Operating instructions
1. On/Off switch:
Switching on: press the trigger switch (2).
Continues operation: after press the trigger
switch (2), lock the on with the lock button (1)
then release the trigger switch (2).
Switching off: release the trigger switch (2).
WARNING! If the "Lock-ON" button (1) is
continuously being depressed, the trigger
(2) can not be released.
2. Adjust the cutting speed
Your tool is equipped with a variable
speed dial (9). The blade stroke rate may
be adjusted during cutting operation by
presetting the dial on or between any one of
the six numbers.
3. Setting SPM rating (strokes per
minute):
1-2. Low stroke
3-4. Medium stroke
5. High stroke
6. Override
4. Plunger speed:
The stroke rate may be adjusted as
described earlier under "Variable Speed
Dial". The best results for a particular
application are determined by experience,
though as a general rule, slower speeds are
for denser materials and faster speeds are
for soft materials.
5.Bevel or angle cutting:
WARNING! To prevent damage to the tool
when bevel or angle cutting, the scroll
mechanism must be locked in place with
the cutting edge of the blade facing the
front of the tool. Disconnect the cord
from the power source.
The foot can be adjusted to cut any angle
from 0° to ± 45° .
TO ADJUST: Loosen the two screws in the
bottom of base by turning the hexagonal key
(13) in anti-clockwise direction as shown,
move base slightly backward to disengage
the locking tab (Fig. 2).
To adjust the base at your wanted angle,
tighten the two screws in the bottom of
base by turning the hexagonal key (13) in a
clockwise direction.
Fig.2
VI - Maintenance and Service
• Before any work on the machine itself, pull
the mains plug.
• For safe and proper working, always keep
the machine and ventilation slots clean.
• Regularly check to see if any dust or
foreign matter has entered the grills near the
motor and around the trigger switch. Use a
soft brush to remove any accumulated dust.
Wear safety glasses to protect your eyes
whilst cleaning.
• If the body of the tool needs cleaning, wipe
it with a soft damp cloth. A mild detergent
can be used but nothing like alcohol, petrol
or other cleaning agent.
• Never use caustic agents to clean plastic
part.
• Lubricate all moving parts at regular
intervals.
CAUTION! Water must never come into
contact with the tool.
Disposal
The crossed-out wheeled bin logo
requires the separate collection of
waste electric and electronic
equipment (WEEE). Such equipment
may contain dangerous and
hazardous substances. These tools
must be returned to a designated
collection point for the recycling of
WEEE and must not be disposed as
unsorted municipal waste. By doing
so, you will help to conserve
resources and protect the
environment. Contact your local
authorities for more information.
General inspection
vibrate loose over time.
GB
98