Stopping The Engine; Cleaning, Maintenance, Storage And Ordering Of Spare Parts - EINHELL 41.713.26 Bedienungsanleitung

Anleitung_BG_PW_18_SPK1:_
6.2 Intake process
During the priming process, the shut-off devices
present in the pressure pipe (spray nozzles,
valves etc.) must be completely open so that the
air in the suction pipe can escape freely.
Depending on the suction height and the air
quantity in the suction pipe, the initial priming
process can last for approx. 0.5 min. – 5 min. In
the case of longer priming periods, top up again
with water.
If the pump is removed after use, it is essential
that it is filled with water again the next time it is
connected and started.

6.3 Stopping the engine

Set the On/Off switch to "OFF".
Close the petrol cock.
7. Cleaning, maintenance, storage and
ordering of spare parts
Disconnect the spark plug boot before doing any
cleaning and maintenance work!
7.1 Cleaning
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
We recommend that you clean the device
immediately each time you have finished using it.
Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts
of the equipment. Ensure that no water can seep
into the device.
7.2 Maintenance
In this connection, please also read the attached
service information
7.2.1 Changing the oil
The engine oil is best changed when the engine is at
working temperature
Use only engine oil (10W40).
Place the machine on a slightly inclined surface
so that the oil drain plug is at the lower end
(Figure 7 / Item A).
Remove the oil filler screw (Figure 7 / Item B).
Remove the oil drain plug and drain the warm
engine oil into a suitable container.
After all the oil has drained, screw in the oil drain
plug and place the machine on a flat surface.
23.06.2008 8:58 Uhr Seite 15
Insert fresh engine oil up to the top mark on the
oil dipstick (Figure 8 / Item H).
Important. Only inset the oil dipstick to check
the oil level. Do not screw it in.
While the machine is working, the oil level must be
between the two marks "L" and "H" (Figure 8).
Dispose of the waste oil properly.
7.2.2 Air filter
Clean the air filter at regular intervals, and replace it
if necessary.
Remove the air filter cover (Figure 9-10)
Remove the filter insert (Figure 11)
Clean the air filter by tapping it, blowing it out
with compressed air or by washing it with soap
suds. Important. Leave the air filter to dry before
you refit it.
Assemble in reverse order.
7.2.3 Spark plug
Clean the spark plug at regular intervals, and replace
it if necessary. Set the electrode gap to 0.6 mm.
Remove the spark plug boot by twisting it (Figure
12)
Remove the spark plug using a spark plug
wrench (Figure 13)
Clean the spark plug with a copper wire brush or
fit a new one.
Assemble in reverse order.
7.2.4 Fuel filter
Remove the fuel line (Figure 14)
Unscrew the fuel filter from the tank (Figure 15)
Clean the fuel filter with compressed air. Ensure
that you do not damage the filter.
Assemble in reverse order.
7.3 Storage
Rinse the pump thoroughly with water before
lengthy periods of inactivity or winter storage.
Close the petrol cock and allow the engine to run
until it stops to empty the carburetor.
Fill the tank fully to prevent rust formation.
Remove the drain plug (Figure 1 / Item 6) and
fully drain the pump housing.
Store the machine in a dry place out of the reach
of children.
GB
15