Setting Up; Resetting Connection; Control The Hood Via The Hob - NEFF T18TS2KN SERIE Gebrauchsanleitung

Connecting appliances via your home network
Use this type of connection if neither or one of the two
appliances is connected to the Home Connect app.
If the appliances are connected to each other via your
home network, you can use both the hood controls and
Home Connect to operate the hob.
Notes
Make sure you follow the safety instructions in the
■
instruction manual for your extractor hood and that
these are complied with even when operating the
appliance via the hood controls on the
hob.~ "Important safety information" on page 50
If the appliance is being operated by means of the
■
controls on the extractor hood, this mode of
operation always has priority. It is not possible to use
the hood controls on the hob during this time.
In networked standby mode, your appliance requires
■
a maximum of 2 W.

Setting up

Both the hob and the extractor hood must be switched
on before you can connect them to each other.
To do this, refer to the section entitled "Connecting to
the hob" in the instruction manual for your extractor
hood.
Connecting directly
If you connect your hob directly to the extractor hood, it
cannot be connected to your home network as well and
you will not be able to use Home Connect.
Switch on the hob.
1.
Touch the symbol for 4 seconds.
U
2.
The product information will be displayed.
Touch the symbol repeatedly until the
U
3.
setting appears.
will be lit on the hotplate display.
‹
Set the value to using the twist knob.
‚
4.
will be lit on the hotplate display.
‚
You have 2 minutes to initiate the connection
5.
process on the extractor hood.
Once the hob is connected to the extractor hood, the
value will appear on the hotplate display. The
„
symbols for the hood controls on the hob are displayed
on the hob's control panel.
Connecting via your home network
You require a router that has WPS functionality.
You require access to your router.If you do not have
this, follow the steps for "Direct connection".
When you begin, make sure that the extractor hood is
connected to the app or is on your home network.
Switch on the hob.
1.
Touch the
2.
The product information will be displayed.
Touch the
3.
setting appears.
‹
network) will be lit on the hotplate display.
Set the value to
4.
‚
If the appliance is not yet connected to your home
5.
network, press the WPS button on the router within
the next 2 minutes.
The hob will be connected to your home network
and the value
The process of connecting to the extractor hood
starts automatically and is active for 2 minutes.
If the appliance is already connected to your home
network, proceed to the next step.
Initiate the process for connecting to the extractor
6.
hood.
Once the connection process is complete, the value
will appear on the hotplate display.The symbols for the
hood controls on the hob are displayed on the hob's
control panel.
Note: Connection can only be established when both
appliances are connected to your home network and
the connection process has been initiated for both of
them. If the connection process has already timed out
for one of the two appliances, try to connect again
(basic settings,

Resetting connection

You can reset the connections you have saved for your
home network and extractor hood at any time.
Touch the
1.
The product information will be displayed.
Touch the
2.
setting appears.
Set the value to
3.

Control the hood via the hob

™‚‡
In the basic settings of your hob you can adjust the
behaviour of your extractor hood depending on the
switch-on/off of the hob or individual cooking zones.
~ "Hood control settings" on page 66
You can select other settings using the control panel.
Setting the fan
Switching on
Touch the
Setting fan level
Use the twist knob to select the fan setting.
You can choose between the levels 1, 2 and 3. To
select the intensive levels, turn the twist knob until
or
˜ƒ
symbol for 4 seconds.
U
symbol repeatedly until the
U
(not connected) or (connected to home
ƒ
using the twist knob.
‚
will flash on the hotplate display.
will appear on the hotplate display.
ƒ
setting).
™‚‡
symbol for 4 seconds.
U
symbol repeatedly until the
U
using the twist knob.
‹
symbol.
A
appears.
Hood connection
en
™‚‡
„
™‚‡
˜‚
65