Blade Selection - Ryobi CJS-180L Bedienungsanleitung

GB
FR DE ES IT
OPERATION
WARNING:
This tool is designed to work with T-shank
blades. Use with non-T-shank blades may result
in blades coming loose from tool, resulting in
personal injury or property damage.

BLADE SELECTION

To obtain the best performance from the saw, it is
important to select a specific blade for the particular
application and type of material you wish to cut. By doing
this you will get a smoother, faster cut and prolong blade
life.
NOTE: This tool is designed to work with T-shank blades.
Other types of saw blades are not guaranteed to work
properly and may come loose from the tool.
INSTALLING BLADES(Fig.5)
Remove battery pack.
Q
Lift blade clamp lock located on front of saw.
Q
Insert saw blade between blade clamp and saw bar.
Q
Close blade clamp lock.
Q
Replace battery pack.
Q
GENERAL CUTTING(Fig.6)
Rest the front of the saw base on the workpiece and align
cutting edge of the blade with the line on your workpiece.
Start the saw and move it forward on the work surface.
Apply downward pressure to keep the saw steady and
only enough forward pressure to keep the blade cutting.
Do not force the saw. Forcing the saw may overheat the
motor and break saw blades. Broken saw blades must
be replaced with new saw blades.
ORBITAL MOTION(Fig.6)
The blade of the saw cuts in orbital motion. This feature
is adjustable and provides faster, more efficient cutting.
With orbital motion, the blade cuts through your work
in the upstroke but does not drag across your work in
the downstroke. The higher settings should be used
when fast cutting in soft material is desired. The lower
settings should be used when cutting materials with
more resistance.
STRAIGHT CUTTING(Fig.6)
A straight cut can be made by clamping a piece of wood
or straightedge to the workpiece and guiding the edge of
the saw against it. Make the cut from one direction only;
961075062-03(CJS-180L)_EU.indd Sec1:3 961075062-03(CJS-180L)_EU.indd Sec1:3
NL PT DK SE FI NO
English
RU PL CZ HU RO LV
don't cut halfway and complete the cut from the opposite
end.
SPLINTER-FREE CUTTING(Fig.7)
The base of the jig saw has a narrow slot to permit
splinter-free cutting. It is especially useful when cutting
plywood. This feature should only be used when making
straight cuts or circle cuts. It is not for bevel cutting or
plunge cutting.
NOTE: The non-orbital setting also helps reduce
splintering when cutting plywood.
positioning the base in the splinter-free cutting position
Remove battery pack
Q
Using the 3 mm. hex key provided, loosen base pivot
Q
screws and slide base forward.
Always set the cutting angle at 0° for splinter-free
Q
cutting. To set cutting angle at 0°, align the 0° mark
on the scale with the edge of the motor housing.
NOTE: When setting angle at 0° for splinter-free cutting,
the positive stop notches on the rear of the base are not
used.
Tighten base pivot screws securely.
Q
Remove hex key and return it to the storage area.
Q
Replace battery pack.
Q
OPTIONAL EDGE GUIDE(Fig.8)
An optional edge guide is available for use with the saw.
It can be used for making crosscuts and rip cuts.
Remove battery pack.
Q
Insert the arm through the two slots in the base of the
Q
saw as shown.
Adjust edge guide to the desired width and lock in
Q
place with the edge guide screw.
Replace battery pack.
Q
SCROLL CUTTING(Fig.9)
Scroll cuts can be made with the jig saw by guiding the
direction of the cut with applied pressure on the handle
as shown.
WARNING:
Excessive side pressure to the blade could result
in broken blades or damage to the material being
cut.
3
LT EE HR SI SK GR
1/5/10 1:37:42 PM 1/5/10 1:37:42 PM
TR