Technical Data - 3M PN 64380 Bedienungsanleitung

The safety and accident prevention instructions are reported in the "GENERAL SAFETY INSTRUCTION" booklet which forms an integral part of these
documents; the operating instructions indicate the additional information required specifi cally for use of the tool.
To reduce the risk associated with impact from abrasive paper disc, breakup, sharp edges and rupture:
- The electric tool must be connected to a suitable dust extraction unit (not supplied): Use regulation safety devices for personal protection and
observe safety norms valid for the processed work material.
- Refer to the appropriate MSDS before use
- Do not operate tool in water or in an excessively damp application
- Never operate this tool without all safety features in place and in proper working order.
- Any operations carried out on the tool must be eff ected with the power supply disconnected.
- Before starting the tool, ensure that it is held tightly and in contact with the work surface.
- Wear clothing suited to the work you are about to perform.
- Due to risks that may arise during sanding, we recommend the use of appropriate P.P.E. (personal protective equipment) including hand, hearing, eye
and respiratory protection according to laws in force to prevent or reduce accident probability.
- Be aware that the appliance continues to work for a few seconds after it has been switched off .
To reduce the risks associated with vibration:
- If any physical hand/wrist discomfort is experienced, work should be stopped promptly. Hand, wrist and arm injury may result from repetitive work,
motion and over exposure to vibration. If this is suspected then seek medical attention.
To reduce the risks associated with loud noise:
- Always wear hearing protection while operating this tool. Follow your employer's safety policy or local/national standards for personal protective
equipment requirements.
To reduce the risks associated with skin abrasion, burns, cuts, or entrapment:
- Use care in attaching the abrasive paper disc; following instructions to ensure that it is securely attached to the tool before use.
- Never over-tighten accessory fasteners.
- To reduce the risk of skin abrasion, do not touch the moving parts during operation for any reason
- Do not use paper disc pads that have a Max RPM less than the tool Max RPM rating
- Only accessories specifi cally recommended by 3M should be used with this tool. Use in any other manner or with other accessories could lead to unsafe
operating conditions.
- At the end of its useful life, the product, pursuant to European Directive 2002/96/CE (RAEE) + 2003/108/CE and its implementation in national law,
must not be released into the environment or thrown away as domestic waste, it must be disposed of at an authorised recycling centre (contact the
relevant local authorities for a list of places where the product may be disposed of according to the law). Disposing of the product correctly contributes
to protecting human health and safeguarding the environment. Any illegal disposal of the product will be punishable by law.
TYPE
PROTECTION CLASS
OPERATING VOLTAGE
ABSORBED CURRENT
ABSORBED POWER
ELECTRONIC SPEED
CONTROL
ROTATION SPEED
ORBITAL DIAMETER
PAD DIAMETER
PAD TYPE
EXTRACTION SYSTEM
WEIGHT
3M Instruction Manual
75-078_ROSander.indd 4 75-078_ROSander.indd 4
WARNING
CAUTION

TECHNICAL DATA

PN 64384 & PN 64385 PN 64380 & PN 64381
II II
230 V ~ 50 Hz 230 V ~ 50 Hz
2 A 2 A
450 W 450 W
YES YES
5000 to 10000 RPM 5000 to 10000 RPM
3mm 5mm
150 mm 150 mm
Hookit™ pad Hookit™ pad
INTEGRAL INTEGRAL
2,1 Kg 2,1 Kg
PN 64386
II
110 V ~ 50 Hz
4 A
450 W
YES
5000 to 10000 RPM
3mm
150 mm
Hookit™ pad
INTEGRAL
2,1 Kg
2
PN 64382
II
110 V ~ 50 Hz
4 A
450 W
YES
5000 to 10000 RPM
5mm
150 mm
Hookit™ pad
INTEGRAL
2,1 Kg
12.03.2010 12:45:56 12.03.2010 12:45:56