Ikra BV 2800 E Gebrauchsanweisung Seite 21

• Arrange the extension cord so that it cannot
be damaged and does not cause a hindrance.
• If the cord is damaged during utilisation, it
must be disconnected immediately from the
mains. DO NOT TOUCH THE CABLE BE-
FORE YOU HAVE DISCONNECTED IT FROM
THE MAINS, since damaged cable result in
contact with live parts.
• Only use a weatherproof extension cord with
a connector unit according to IEC 60320-2-3.
• Only extension cords of type H05W-F, H05RN-
F or IEC (60227 IEC 53, 60245 IEC 57) may
be used.
• If you want to use an extension cable when op-
erating your product, only the following cable
dimensions should be used:
2
– 1.0 mm : max. length 40 m
2
– 1.5 mm : max. length 60 m
2
– 2.5 mm : max. length 100 m
• Note: If an extension cable is used it must be
earthed and connected through the plug to the
earth cable of your supply network in accord-
ance with prescribed safety regulations.
• Couplings and plugs must be splashwater-
proof.
• Make sure to have a safe stand when working
on inclines.
• Move the tool at walking speed only.
• Inspect the collection bag regularly. If the
collection bag becomes worn or damaged,
replace.
• Warning! Do not touch moving dangerous
parts before the mains plug has been un-
plugged and the moving dangerous parts have
come to a complete standstill.
• Warning! NEVER use the machine in bad
weather, particularly, if there is a risk of light-
ning!
• Warning! Never operate the machine with de-
fective safety equipment or covers or without
safety equipment.
• Keep the extension cord away from moving
dangerous parts to avoid damage to the ca-
bles, which can result in contact with live parts.
• Do not operate the machine barefoot or while
wearing open sandals. Avoid wearing loose
fitting clothing or clothing with hanging strings
or ties.
• Operate the machine in the recommended po-
sition and only on a firm, level surface.
• Prior to use, always perform a visual inspection
to determine whether the shredder, the bolts of
the shredder and other fasteners are secured,
that the housing is not damaged and that the
safety equipment and protective screens are
mounted. Replace worn or damaged compo-
nents in sets to maintain the balance. Replace
damaged or unreadable labels.
• Prior to starting the machine, make sure that
the feeding unit is empty.
• Keep your face and body away from the filling
opening.
• Make sure your hands, other body parts or
clothing are not in the feeing unit, the discharge
channel or in the vicinity of moving parts.
• When feeding material, never stand on a level
that is higher than the level of the machine
base.
• When operating the machine, do not remain in
the discharge zone.
• When feeding material into the machine, use
extreme caution to make sure that no metal
pieces, stones, bottles, cans or other foreign
objects enter the machine.
• Do not let processed material accumulate in
the discharge zone, since it can prevent proper
discharge and result in material being fed into
the unit again via the filling opening.
• Switch the machine off and unplug the mains
plug if the machine is blocked before clearing
debris from it.
• Keep the power source free of debris and other
accumulations to prevent it from being dam-
aged or a possible fire.
• Do not tilt the machine while the power source
is operating.
• If the machine is stopped for maintenance,
inspection, storage or changing accessories,
switch off the power source and disconnect the
machine from the mains and make sure that
all moving parts have stopped moving. Allow
the machine to cool down before inspections,
adjustments, etc. Maintain the machine with
care and keep it clean.
• Always allow the machine to cool down before
putting into storage.
• When performing maintenance on the shred-
der, keep in mind that although the power
source is switched off by the safety device's
locking function, the shredder can still be
moved.
• For safety reasons, replace parts that are worn
out or damaged. Only use original spare parts
and accessories.
GB-5