Inhaltsverzeichnis
Werbung
Livance – GDP 31...
Service and Special Functions
Software Upgrade
Attention: if a failure should occur during the software upgrade
(e.g. a mains failure), it may happen that the unit's function and a
restart of the upgrade function are no longer possible. If this
should be the case, you must replace the integrated FLASH IC
(U15) with a preprogrammed IC (see corresponding spare parts
list).
– Insert the upgrade CD (see corresponding spare parts list) and
observe the hints on the display and on the screen of the TV set.
Warranty / costs
We expressly point out that only operating software authorized by
GRUNDIG is allowed. If a failure is caused by an operating software
which has been downloaded from not authorized sources, indepen-
dent of its origin, or a modified software, this represents an outside
interference. An outside interference leads to the expiration of any
warranty claims. For this reason, GRUNDIG is obliged to generally
refuse any payment due to such infringements. In such cases, the
repair costs are at the charge of the retailer or the final customer, even
within the period of warranty.
Initialization of the Set
Press the
7
/
8
buttons on the set at the same time and connect the
set to the mains. This resets the software of the set to the factory
presettings. The basic settings are loaded and the customer-specific
data is cleared.
Service Menu
The Service menu is subdivided into the freely accessible "System
information" menu and the password-protected "Dealer service menu".
1. Functions of the buttons
For navigating in the Service menu, the buttons on the remote control
are used.
i
Call up the Player menu / End the menu functions.
S
A
/
Select menu functions.
a
Select higher menu function.
s
Activate menu function.
OK
Activate menu function.
x
Select higher menu function.
1...9
Activate menu function directly.
y
Exit demo function in stop mode.
2. Calling up the Service menu
– Call up the "Player Menu" using the »i« button.
– Select "Installation" using the
S
A
or use the
/
buttons and confirm with the »OK« button.
– Select "Additional functions" using the
S
A
or use the
/
buttons and confirm with the »OK« button.
– Select the "Service Menu" using the
S
A
or use the
/
buttons and confirm with the »OK« button.
The Service menu is subdivided in sub-menus according to the menu
overview (Point 3).
2.1 System information
– Call up the "Service menu" (Point 2).
– Select "System information" using the
S
A
or use the
/
buttons and confirm with the »OK« button.
The System information menu appears on the picture screen.
System information
GDP 3100
Unit
SW-Version: 0.79 / 258 Oct 17 2001
Software version
HW-Version: 0.03
Hardware version
Copyright: GRUNDIG AG 2001
Hardware information
http://www.grundig.com
NDV8602/DVD-5/Pantera-II LE rev 1 R:2
Regional code
select
and choose
GRUNDIG Service
5
button,
4
button,
2
button,
1
button,
exit
back
Service- und Sonder-Funktionen / Service and Special Functions
2.2 Retailer service menu
– Call up the "Service menu" (Point 2).
– Call up the "Retailer Service" menu using the
S
A
or use the
/
buttons and confirm with the »OK« button.
– Enter the digits "8 5 0 0".
Note: the further menus can be called up according to the menu
overview (Point 3).
2.2.1 System settings
– System messages
When selecting a function or in the case of an error (e.g. disc,
handling or unit error), the system emits messages which are briefly
displayed in the bottom area of the picture screen.
– Demo
When the demo function is activated, the eject button and the on/off
switch are locked.
Ending the demo function:
– press the
7
button.
y
– press the
button.
2.2.4 Video special
– Format conversion
The following format conversions are possible:
– Centre
– Auto
– 525 lines only
– 625 lines only
– Video signal
• DAC enable
The following digital-to-analog converters can be activated/deac-
tivated:
– DAC1 = Green/Y signal
– DAC2 = Blue/C signal
– DAC3 = Red signal (indication of the active switching state)
• NTSC format (60Hz format)
The following 60Hz formats can be selected:
– 525 lines, NTSC standard
– 525 lines, M-PAL standard
• NTSC composite signal
The following NTSC composite signal formats can be selected:
– NTSC USA
– NTSC Japan
– NTSC Other
• PAL format
The following PAL formats can be selected:
– PAL BDGHI
– PAL N
– PAL N-Combo
2
button,
2 - 3
Werbung
Inhaltsverzeichnis
