Werbung
(8) EQ-IN switch
Switch, to loop-in the 7-band graphics equalizer into the (MAIN MIX) signal path.
The function is displayed via the red LEDs of the sliding-dolly regulator.
(9) AUX-SEND-GAIN-CONTROL adjuster
Makes the setting of the AUX output level up to +15 dB for secondary signal processing possible.
(10) FX-SENDS-GAIN-CONTROL adjuster
Makes the setting of the effect (FX) output level of up to +15 dB for secondary signal processing possible.
(11) AUX-PFL switch
Swit ches PFL to AUX bus.
(12) FX-PFL switch
Switches PFL to effect (FX) bus.
(13) AUX-RETURN adjuster
To adjust the volume of the returning AUX signals.
(14) FX-RETURN adjuster
To adjust the volume of the returning effect (FX) signals.
(15) ALT3-4 channel fader
To adjust the volume of the ALT3-4 channels.
(16) MAIN-MIX fader
To adjust the volume of the left main channel.
(17) MAIN-MIX fader
To adjust the volume of the right main channel.
(18) 2TK switch
Switches PFL to TAPE-in input (16)
(19) ALT3-4 PFL switch
Switches PFL to ALT3-4 channels.
(20) ALT3-4 TO MIX switch
Switches ALT3-4 to MAIN MIX bus
(21) Headphone volume control
To adjust the volume of the headphones and the CTRL ROOM OUT (control room) output (20).
(22) 2TK TO MIX switch
Switches TAPE-in input (16) to MAIN MIX bus.
(23) MAIN MIX switch
Switches PFL to MAIN MIX bus.
(24) ALT3-4 PFL switch
Switches PFL to ALT3-4 bus.
(25) PFL SOLO switch
Switches PFL with correct stereo to the channels. The solo LED shows whether the switch is pressed.
(26) Stereo LED modulation indicator
Visually displays the complete level-range of the mixing desk from –30 to +20 dB.
(27) PHONES jacks
Jack for headphone connection.
(28) +48V LED
LED lights up when phantom powering is switched on with phantom switch (8) on terminal panel on the
back.
(29) POWER LED
LED lights up when mixing desk with power switch (9) on terminal field on the back is switched on.
(30) UP push-button
(31) DOWN push-button
Up and down push-button to select the effects of the effects processor.
(32) ENTER push-button
After pressing of Enter button the selected effect is activated.
22
Termination Panel on the Back
(1) CHANNEL-INSERT jacks
To loop in further units to influence the signal, such as compressors, gates, parametric equalizer etc. The
signal is looped-out (sent) and looped back in (returned) before the channel fader and before the equalizer.
(2) ALT3-4 INSERT jacks
To loop-in further units to influence the signal such as compressors, gates, parametric equalizer etc. The
signal is looped-out (sent) and looped back in (returned) before the channel fader and before the equalizer.
(3) ALT3-4 OUTPUT jacks
Alt3-4 bus signal output.
(4) MAIN-INSERT jacks
To loop-in further units to influence the signal such as compressors, gates, parametric equalizer etc. The
signal is looped-out (sent) and looped back in (returned) before the channel fader and before the equalizer.
(5) MAIN OUTPUT jacks (unsymmetric)
MAIN MIX bus signal output. Stereo mixing desk output before power amplifier.
(6) MAIN OUTPUT jacks (symmetric)
MAIN MIX bus signal output. Stereo mixing desk output before power amplifier.
(7) MAIN OUTPUT-LEVEL switch
To switch over the MAIN MIX bus output level between –10dB and +4dB at the MAIN output jack (6).
(8) PHANTOM switch
Switches on the necessary phantom powering for all MIC channels for the condenser microphones.
(9) POWER switch
Switches the power supply for the mixing desk on/off.
(10) INPUT adjuster
To adjust the power amplifier volume.
(11) INPUT jacks
External symmetrical 6.3mm jack input of the power amplifier. If this input is used, the internal signal path
from the mixing desk output is interrupted.
23
Werbung
Kapitel
