Hauck Shopper RS Gebrauchsanweisung Seite 11

IINStRUCtIoN oF USE
1. ERECTING (fig. 1).
Release transportation-lock.
2. UNFOLDING (fig. 2)
open the stroller until the locking latches on both sides have locked in place.
3. FRONT WHEEL ASSEMBLY (fig. 3a,3b)
Push both front wheels into position (3a). Make sure it locks in place and cannot be pull off. When changing
the wheel, lie the stroller down in fully assembled state. Press the lever (3b) on the wheel and pull it off.
4. FRONT WHEEL ADJUSTMENT (fig. 4)
Slide the front wheel lever up to lock the swivel movement. to release the swivel movement, slide the lever
down.
5. REAR WHEEL ASSEMBLY (fig. 5a-5e)
Put the washer on the axle (5a), then put the wheel in (5b) and then secure the wheel by a locking spring (5c).
Place the covering cap onto the wheel (5d).
Push both plastic brackets at the same time until they are locked onto the rear legs (5e). Make sure the
pushpin locks in the plastic housing hole securely.
When changing the wheel, reverse the sequence.
6. BRAKE (fig. 6)
Press the rear brake down by foot to stop the rear wheels and push the stroller to check.
Attention: Always apply both brakes when parking the stroller.
7. ADJUSTING THE BACK REST (fig. 7)
Pull the metal handle at the back of the backrest upwards and adjust the backrest to the desired position. the
backrest can be altered to 4 different positions.
8. ADJUSTING THE LEG REST (fig. 8)
Press both (left & right) buttons to bring the leg rest to the desired position.
9. INSTALL THE FRONTBAR (fig. 9a, 9b)
Install the front bar just below the locking latches by pushing in the front bar into the housings (9a). You will
hear a click sound when they are secured onto the frame. Test the front bar by pulling on it to make sure it is
locked into place. To release the front bar, push the buttons underneath and pull out the front bar (9b).
10. ASSEMBLE THE CANOPY (fig. 10a, 10b)
Snap the button at the end of the canopy to the stroller frame. Slide the canopy plastic housings on the
catches above the locking latch on each side.
11. REVERSING THE HANDLE (fig. 11a, 11b)
Press the lock on the right-hand side of the upper handlebar (11a). With the button held in, pull both swiveling
handlebar locks upward (11b). Now push the handle forward and then swivel the handle to the opposite
direction.
Please always check if the handle has securely engaged in the new position. Front & rear wheels must be
additionally secured with both of the parking brakes when park the stroller, if the handle is in the position
facing towards the child.
12. FOLDING AWAY (fig. 12a, 12 b):
Make sure the backrest is always in a recline position. Fold the canopy backward. Slide the 2nd lock to the
left with your thumb (1) and at the same time press folding lock (2). Press the handle down to fold the stroller
(12b). Close the transportation-lock on the side of the frame.
13. SECURE THE CHILD IN THE SEAT (fig 13):
Place the child in the seat and push the clips on the waist belt into the buckle on the crotch belt (the one that
comes between the child's legs). Adjust the length of the belt to your child's needs. Always ensure the straps
are not twisted or caught on the stroller frame. Check the adjustment every time you place the child in the
seat and when the backrest is reclined. To release the harness, squeeze & open the buckle.
Harness adjustment: Insert both fasteners (B) into the buckle (A), ensure that both buttons click into position.
Ensure both shoulder straps (C) are attached to the fasteners (B). Each strap has its own length adjuster
(D). To undo the harness, press the button and pull apart. "D" Rings are provided for fitment of a full safety
harness. The attachment points (D-rings) are located on side straps.
WARNING: (A child's safety is your responsibility.) The child should be harnessed in at all times and should never
be left unattended. the child should be clear of moving parts while making adjustments. this stroller requires
regular maintenance by the user.
GB
11