Specific Safety Instructions; Technical Data - REMS Nano Betriebsanleitung

eng
changing accessories, or storing power tools. Such preventive safety meas-
ures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power
tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tools
operation. If damaged, have the power tool repaired by a qualified expert
or by an authorised REMS after-sales service facility before use. Many
accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g) Secure the workpiece. Use clamps or a vice to hold the workpiece. This is safer
than holding it with your hand, and also it frees both hands to operate the equipment.
h) Use the power tool, accessories and tool bits etc., in accordance with these
instructions and in the manner intended for the particular type of power
tool, taking into account the working conditions and the work to be performed.
Use of the power tool for operations different from those intended could result in
a hazardous situation. All unauthorised modifications to the power tool are
prohibited for safety reasons.
E) Battery tool use and care
a) Ensure the switch is in the off position before inserting battery pack. Inserting
the battery pack into power tools that have the switch on invites accidents.
b) Recharge only with the charger specified by the manufacturer. A charger
that is suitable for one type of battery may create a risk of fire when used with
another battery pack.
c) Use battery tools only with specifically designated battery packs. Use of
any other battery packs may create a risk of injury and fire.
d) When battery pack is not in use, keep it away from other metal objects like
paper clips, coins, keys, nails, screws, or other small metal objects that
can make a connection from one terminal to another. Shorting the battery
terminals may cause bums or a fire.
e) Under abusive conditions, liquid may be ejected from the battery, avoid
contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected from the battery may
cause irritation or bums.
f) Do not use the battery/charger at battery/charger temperatures or ambient
temperatures of ≤ 5°C/40°F or ≥ 40°C/105°F.
g) Do not dispose of defective batteries in the normal domestic waste. Take
them to an authorised REMS after-sales service facility or to a reputed
waste disposal company.
F) Service
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power tool
is maintained.
b) Comply with maintenance instructions and instructions on tool replace-
ments.
c) Check mains lead of power tool regularly and have it replaced by a qualified
expert or an authorised REMS after-sales service facility in case of damage.
Check extension cable regularly and replace it when damaged.

Specific Safety Instructions

WARNING
● Use only electrical plugs with shockproof socket. Check the earth (ground)
connection of the plug.
● Use only extension leads with shockproof socket.
● Only operate the machine off the mains using a 30 mA fault current protected
switch (FI breaker).
● Do not overload the electric pipe cutting machine. Do not use damaged cutting
wheels. Use moderate feeding pressure.
● Caution! Keep hair, clothing and gloves away from the pipe rest when a pipe is
rotating in the rollers. Loose clothing, jewellery or long hair could get caught
between the rotating pipe and the rollers.
● Do not reach into the rotating cutting wheel.
● Where necessary use a material support REMS Herkules (Art. No. 120100) on
each side to support long pipes and position the pipe and material support(s)
exactly with the pipe support (6) of the electric pipe cutting machine.

1. Technical Data

1.1. Article Numbers
REMS Nano
REMS Akku-Nano
REMS High-Power-Battery Li-Ion 10,8 V, 1,3 Ah
Rapid-charger Li-Ion/Ni-Cd 230 V, 50 – 60 Hz, 65 W
REMS cutting wheel Cu-INOX
REMS cutting wheel V
REMS Herkules material support on tripod
REMS Herkules Y material support clamping fixture
REMS Jumbo folding workbench
1.2. Application Area
REMS Nano, REMS Akku-Nano:
Pipes of pressfitting systems made of
● stainless steel, C-steel (not jacketed)
● semi-hard and hard copper
● composite pipes
1.3. Speed
REMS Nano, REMS Akku-Nano:
Idle speed of cutting wheel
1.4. Electrical Data
REMS Nano:
230 V 1~; 50 – 60 Hz; 130 W
fuse protection (mains) 10 A (B), intermittent service AB 2/10 min,
interference suppressed, earth wired from machine No. 3650
REMS Akku-Nano:
10,8 V =, 16 A, 270 W
Rapid-charger Li-Ion/Ni-Cd (1 h)
1.5. Dimensions
REMS Nano:
L × W × H:
REMS Akku-Nano:
L × W × H:
1.6. Weights
REMS Nano
REMS Akku-Nano drive machine without battery
1.7. Noise Data
Workplace-related emission
value
1.8. Vibrations
Weighted effective value of the acceleration
The indicated weighted effective value of acceleration has been measured
against standard test procedures and can be used by way of comparison with
another device. The indicated weighted effective value of acceleration can also
be used as a preliminary evaluation of the exposure.
Attention: The indicated weighted effective value of acceleration can differ during
operation from the indicated value, dependent on the manner in which the device
is used. Dependent upon the actual conditions of use (periodic duty) it may be
necessary to establish safety precautions for the protection of the operator.
2. Commissioning
2.1. Electrical Connection
Note the mains voltage! Before connecting the drive unit or the rapid charger,
check whether voltage on the rating plate matches the mains voltage. At work
sites, in damp surroundings, in the open or in the case of comparable types of
use, only operate the equipment off the mains using a 30 mA fault current
protected switch (FI breaker).
Rechargeable batteries
The rechargeable battery supplied with REMS drive units and spare recharge-
able batteries are not charged. Charge the battery before use. Only use a
REMS rapid charger for charging. The rechargeable batteries only reach their
full capacity after being charged several times. Li-ion batteries should be
recharged regularly in order to avoid their total discharge. The rechargeable
battery will be damaged by exhaustive discharge. Non-rechargeable batteries
may not be charged.
NOTICE
the drive unit or the rapid charger. If inserted at an angle it can cause damage
to the contacts and result in a short circuit which damages the battery.
Rapid charger Li-ion/NiCd (Art. No. 571560)
The left control lamp lights up and remains green when the mains plug is
plugged in. If a battery is inserted in the rapid charger, the green control lamp
flashes to indicate that the battery is charging. The green light stops flashing
and remains on to signal that the battery is fully charged. If the red control lamp
flashes, the battery is defective. If the red control lamp comes on and remains
on, this indicates that the temperature of the rapid charger is outside the permis-
sible range of +5°C to +40°C.
NOTICE
2.2. Installation of the Machine
Place the electric pipe cutting machine on a workbench or similar or unscrew
844000
the pipe arm (2) and clamp the base frame (1) in a vice or bolt the base frame
844001
to the workbench with bolts through holes (3). Where applicable, longer pipes
844510
must be supported on both sides with REMS Herkules (Art. No. 120100).
571560
844050 2.3. Installing (changing) the cutting wheel (4)
844051 Pull out the mains plug or remove the battery! Select a suitable cutting wheel:
120100 ● REMS cutting wheel Cu-INOX for stainless steel pipes, steel pipes and
120130 copper pipes of the pressfitting systems.
120200 ● REMS cutting wheel V for multi-layered composite pipes of the pressfitting
systems.
Remove hexagonal nut (5) with size SW 8 ring spanner. Insert (change) cutting
wheel (4). Make sure that the carrier pins of the drive shaft grip into the holes
of the cutting wheel. Replace the hexagonal nut (5).
Ø 12 – 28 mm
Ø 12 – 35 mm NOTICE
Ø 12 – 40 mm
or the pipe will not be cut. Only use original REMS cutting wheels!
Input
Output
405 × 90 × 103 mm (15.9"× 3.5"× 4")
408 × 88 × 105 mm (16"× 3.4"× 4.1")
L = 78 dB L = 67 dB L
wA pA
Always hold the rechargeable battery upright when inserting it in
The rapid chargers are not suitable for outdoor use.
If an unsuitable cutting wheel is used, the wheel will be damaged
eng
130 rpm
230 V~; 50 – 60 Hz; 65 W
12 – 18 V=
1.9 kg (4 lb)
1.96 kg (4.1 lb)
= 87 dB K = 3 dB
pC, peak
1.2 m/s² K = 1.5 m/s²