STEINEL HF 360 AP Bedienungsanleitung Seite 9

Installation
Note for IR 180 AP: Connecting the supply
The installation position lead to the basic element
should be at least 1 m from (refert to ill. on page 4):
a light, since heat radiation The mains lead consists of a
may trigger the system. 3 phase cable.
L = phase conductor
Installation procedure:
1. Loosen housing screws N = neutral conductor
and open housing a,
then loosen sensor unit L' = phase conductor
c (screw) and remove
with the basic element
If in doubt, the cable must
be identified with a voltage
b.
2. Hold base of housing on tester. Switch off the current
wall (with the inscription again. Phases (L) and (L')
TOP facing upwards) and in addition to the neutral
mark the drilling holes. conductor (N) are connected
3. Drill holes with a 6 mm to the terminal block. A
bit. protective-earth conductor
4. Insert dowels in the is not required.
holes.
5. Screw the base of the Important: Reversing the
housing in place with the connections may result in
enclosed screws. damage to the unit.
6. Strip the cable (approx.
70 mm) and remove
8. Insert basic element b
approx. 5 mm of insula-
into the housing section
tion from the flexible
a (terminal connection
ends. at bottom).
7. Push through sealing 9. Carefully push on the
plugs and pass the cable sensor module c (tak-
through (the cable sheath ing care not to jam) and
must be completely sur- screw to the housing
rounded by the sealing base section.
plug).
10. After the mains connec-
tion has been made, the
sensor switch can be
operated (refer to func-
tions section).
11. Finally apply the design
(usually black or brown) shade d and screw in
place.
(usually blue)
Note:
Parallel switching of
(usually black or brown)
IR 180 AP and HF 360 AP
is possible. Nevertheless, a
neutral lead must be pres-
ent on each flush box. The
max. output to be switched
does not increase as a
result.
- 16 -
Functions
Reach setting
(Sensitivity) i
The term reach denotes
the approximately circular
diameter that results as the
detection zone.
1 - 8 m
Functions
Twilight setting
(Response threshold) g
2
The desired sensor re-
LUX
sponse threshold can be
2
2
adjusted continuously from
Lux
LUX
approx. 2 lux to 2000 lux.
Adjusting screw right stop
position means: daylight
operation approx. 2000 lux
(factory setting).
2 - 2000 lux
Time setting
(Switch - off delay) h
The desired duration of
illumination of the connected
light can be continuously
adjusted from approx.
30
10 sec. to max. 30 min.
Adjusting screw left stop
30
position means: shortest
time approx. 10 sec. (factory
setting)
10 sec. - 30 min.
Adjusting screw right stop
position means: longest time
approx. 30 min.
The timer is restarted by any
motion detected before this
time elapses.
(only for HF 360 AP)
Adjusting screw left stop
position means: minimum
reach (approx. 1 m / factory
setting).
Adjusting screw right stop
positon means: maximum
reach (approx. 8 m).
Adjusting screw left stop
position means: night-time
operation approx. 2 lux.
When adjusting the detec-
tion zone and for the per-
formance test in daylight,
the adjusting screw must be
set to the RH stop position.
The shortest time setting is
recommended when adjust-
ing the detection zone and
performing a functional test.
Note: After every 'OFF'
switching, further motion
detection is interrupted for
approx. 2 seconds. Only
after this time elapses is
it possible for the Sensor
Switch to switch light again.
- 17 -