Operation - Conrad 548484 Bedienungsanleitung

USB 3.0 7 Port Hub with power adaptor
Item no. 548484
Intended use
This product is intended to be connected to a computer with a USB port and makes seven USB
ports available for use. When connected to a USB 3.0 port of a computer, this product enables
a theoretical transmission speed of up to 5 GBit/s. The power supply is obtained via USB 3.0
or through the supplied adaptor.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you
use the product for purposes other than those described above, the product may be damaged.
In addition, improper use can cause hazards such as short circuiting, fire, electric shock etc.
Read the instructions carefully and keep them. Make this product available to third parties only
together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
Delivery content
• USB 3.0 hub
• USB cable
• Power adaptor
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
a) Persons / Product
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become
dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed if
the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
• Before plugging in the device, verify that the information on the product's rating
plate correspond with your household power supply.
• As power supply, only use the supplied mains adaptor.
• Only connect the power adaptor to a normal mains socket connected to the public
supply. Before plugging in the power adaptor, check whether the voltage stated on
the power adaptor complies with the voltage of your electricity supplier.
• Never connect or disconnect power adaptors if your hands are wet.
• Never unplug the power adaptor from the mains socket by pulling on the cable;
always use the grips on the plug.
• When setting up the product, make sure that the cable is not pinched, kinked or
damaged by sharp edges.
• Always lay the cables so that nobody can trip over or become entangled in them.
This poses a risk of injury.
• For safety reasons, disconnect the power adaptor from the mains socket during
storms.
• If the power adaptor is visibly damaged, do not touch it. Risk of fatal injury due
to electric shock! First turn off the power supply to the power outlet that the
power adaptor is connected to (flip off the fuse and then turn off the residual
current operated circuit breaker to disconnect the power outlet at all phases).
Version 12/15
Now unplug the device from the power outlet. Dispose of the power adaptor in an
environmentally friendly fashion, discontinue use of it immediately. Replace it with
an identical power adaptor.
• The adaptor corresponds to Safety Class II. Only a proper mains socket (230 V/AC,
50 Hz) of the public supply net must be used as voltage source.
• Never use the product immediately after it has been brought from a cold room into
a warm one. The condensation generated could destroy the product. The power
supply unit also involves danger to life by electric shock!
• Allow the device to reach room temperature before connecting and using it. This
may take several hours.
• The mains outlet must be located near to the device and be easily accessible.
• When setting up the device, ensure that the cable does not get kinked or crushed.
• Pull the adaptor out of the power outlet when the product will not be in use for
longer periods of time.
b) Miscellaneous
• Consult an expert when in doubt about operation, safety or connection of the
device.
• Maintenance, modifications and repairs are to be performed exclusively by an
expert or at a qualified shop.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.

Operation

When using without an adaptor in a USB 3.0 port:
Ensure that the entire current consumption of all connected USB devices
does not exceed 900 mA.
1. Connect the USB hub via the supplied USB cable to a free USB port of your computer (it
does not need to be switched off).
2. Connect the low-voltage plug of the adaptor with the DC socket of the USB hub.
3. Connect the adaptor to a suitable power outlet. The power indicator light of the adaptor
goes on.
4. Windows recognizes the new hardware and automatically installs the drivers. The drivers
are available in Windows, therefore no driver storage medium is provided.
5. Now connect your USB device to a USB port of the USB hub. The blue LED of the connected
USB port lights up after a few seconds.
When powering the USB hub using the supplied adaptor, a higher current is
available in each USB port of the USB hub. This higher current is required for
some USB devices. For further information, refer to the instruction manual for your
USB device.
When connected to a USB 2.0 port, the supplied adaptor must be used. When
connecting to a USB 3.0 port, the USB hub can be operated without the supplied
adaptor. In this case, the USB hub operates in the so-called "bus-powered mode".
This means that the current supplied by the computer via USB (for USB 3.0, the
standard is 900 mA) is distributed over seven ports.
This is sufficient e.g. for most mouse controllers or keyboards, however many other
devices would not function properly (such as e.g. external hard disks, card reading
devices, USB cameras, etc.).
Should you notice that a device connected to the USB hub is not functioning
properly or is not recognized, operate the USB hub using the adaptor.
Fast charging function
• The USB-ports 6 and 7 are marked with a battery symbol. These USB-ports can be used
for fast charging of suitable USB devices. The USB-ports 6 and 7 deliver a charging current
of max. 1.5 A each, if the connected computer is in sleep mode or switched off. To enable
the fast charging function the power adaptor needs to be connected with the product and a
mains socket.
• The fast charging function is not available as soon as the computer will be switched on. The
USB-ports 6 and 7 act as USB connection for data transmission or for normal charging with
a maximum output current of 900 mA.