Bosch 3 601 JC3 0 Series Originalbetriebsanleitung Seite 19

OBJ_BUCH-1702-004.book Page 19 Friday, September 15, 2017 2:17 PM
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60335-2-69:
2 2
a <2.5 m/s , K=1.5 m/s .
h
Assembly
 Before any work on the vacuum cleaner itself, pull the
mains plug.
Mounting the Vacuum-hose Holder (see figure A)
– Slide the vacuum-hose holders 4 firmly from above into the
retainers 30 intended for this purpose, until they engage.
Mounting the Vacuum Hose (see figure B)
– Mount the vacuum hose 21 onto the hose connection
piece 2 and turn it in clockwise direction to the stop.
Note: While vacuuming, an electrostatic charge develops in
the vacuum hose and accessories caused by the friction of the
dust, which the operator could experience in the form of stat-
ic discharging (dependent on environmental influences and
physical perception).
As a general rule, Bosch recommends using an anti-static vac-
uum hose (accessory) when vacuuming fine dusts and dry
materials.
Mounting VAC Accessories
The vacuum hose 21 and the SFC+ module 20 are fitted with
a clip system that can be used to connect vacuuming accesso-
ries (extraction adapter 19, curved nozzle 22).
Mounting the Extraction Adapter (see figure C)
– Mount the SFC+ module 20 onto the vacuum hose 21 until
both snap-fasteners 31 of the vacuum hose can be heard
to engage.
– Then push the extraction adapter 19 onto the SFC+ mod-
ule 20 until you hear the two snap fasteners 31 on the
SFC+ module clicking into place.
– To disassemble, press both snap-fasteners 31 inward and
pull the components apart.
Mounting Nozzles and Tubes (see figure D)
– Push the curved nozzle 22 onto the vacuum hose 21 until
you hear the two snap fasteners 31 on the vacuum hose
clicking into place.
– Then attach the required vacuuming accessory (floor noz-
zle, crevice nozzle, suction tube, etc.) firmly to the curved
nozzle 22.
– To disassemble, press both snap-fasteners 31 inward and
pull the components apart.
Inserting/Removing a Disposal Bag or Dust
Bag (Dry Vacuuming) (see figures E1 – E2)
For dry vacuuming, a disposal bag 23 or a dust bag (accesso-
ry) can be used. This makes the disposal of the dust easier.
Note: When using a paper filter bag, the semi-automatic filter
cleaning (SFC+) (see "Deactivating the SFC+", page 21),
must, and when using a fleece filter bag, should be shut off.
Bosch Power Tools
Inserting a Disposal Bag
– Unlock the latches 9 and remove the vacuum lid 8.
– Insert the disposal bag 23 into the container 1 with the fill-
ing opening toward the front.
– Pull the filling opening over the connection flange into the
recess of the connection flange.
– Make sure that the disposal bag 23 faces completely
against the interior sides of the container 1.
– Fold the rest of the disposal bag 23 over the edge of the
container 1.
– Reattach the vacuum lid 8 again and lock the latches 9.
Removing and Closing the Disposal Bag
– Unlock the latches 9 and remove the vacuum lid 8.
– Pull the full disposal bag 23 toward the rear off of the con-
nection flange.
– Carefully remove the disposal bag 23 out of the vacuum
cleaner without damaging it.
When doing this, pay attention that the disposal bag does
not get caught or ripped open against the connection
flange or other sharp objects.
– Pull the cover off of the adhesive strip, close the disposal
bag and tape it shut.
Afterwards, tie off the disposal bag 23 below the filling
opening with the pulled off cover of the adhesive strip.
Replacing/Inserting the Dust Bag (Accessory)
– Unlock the latches 9 and remove the vacuum lid 8.
– Pull off the full dust bag from the connection flange toward
the rear. Close the opening of the dust bag by folding down
the lid. Remove the closed dust bag from the vacuum
cleaner.
– Work the new dust bag over the connection flange of the
vacuum cleaner. Make sure that the dust bag faces com-
pletely against the interior sides of the container 1 over its
full length.
– Reattach the vacuum lid 8 again and lock the latches 9.
Inserting the Rubber Lip (Wet Vacuuming)
(see figure F)
Note: The requirements for the ingress degree (dust
category L) have only been proven for dry vacuuming.
– Carefully pry the brush inserts 27 out of the floor nozzle 28
using a suitable tool.
– Insert the rubber lips 26 into the floor nozzle 28.
Note: The structured side of the rubber lips must face out-
ward.
Attaching an L-Boxx (see figure G)
For transport of the vacuum cleaner and for place-saving stor-
age of VAC accessories and/or power tools, an L-Boxx can be
mounted on the vacuum cleaner lid.
– Mount the L-Boxx onto the retainers 7.
 Do not carry the vacuum cleaner by the carrying handle
of the mounted L-Boxx. The vacuum cleaner is too heavy
for the carrying handle of the L-Boxx. Danger of injury and
causing damage.
English | 19
1 609 92A 3WO | (15.9.17)