Makita LH1040 Bedienungsanleitung Seite 16

When the wood facing is attached, do not turn the
•
turn base with the handle lowered. The blade
and/or the wood facing will be damaged.
7. Cutting repetitive lengths
Fig.44
When cutting several pieces of stock to the same
length, ranging from 240 mm to 400 mm, use of
the set plate will facilitate more efficient operation.
Install the set plate on the holder as shown in the
figure.
Align the cutting line on your workpiece with either
the left or right side of the groove in the kerf board,
and while holding the workpiece from moving,
move the set plate flush against the end of the
workpiece. Then secure the set plate with the
screw. When the set plate is not used, loosen the
screw and turn the set plate out of the way.
NOTE:
Use of the
•
accessory) allows cutting repetitive lengths up to
2,200 mm approximately.
CUTTING AS TABLE SAW (BENCH MODE)
CAUTION:
When using the tool in the table saw mode (bench
•
mode), place the blade cover on the turn table so
that the blade cover is centered over the slit for the
blade entrance in the turn table and two small
bosses on the underside of the blade cover fit into
the semi-circular slit in the periphery of the turn
table as shown in the figure and then lock the
handle in the lowest position by fully pushing in the
stopper pin. If not fixing the blade cover, the table
can not be down.
Fig.45
CAUTION:
Always use "work helpers" such as push sticks
•
and push blocks when there is a danger that your
hands or fingers will come close to the blade.
Always hold the workpiece firmly with the table
•
and the rip fence. Do not bend or twist it while
feeding. If the workpiece is bent or twisted,
dangerous kickbacks may occur.
NEVER withdraw the workpiece while the blade is
•
running. If you must withdraw the workpiece
before completing a cut, first switch the tool off
while holding the workpiece firmly. Wait until the
blade has come to a complete stop before
withdrawing the workpiece. Failure to do so may
cause dangerous kickbacks.
NEVER remove cut-off material while the blade is
•
running.
NEVER place your hands or fingers in the path of
•
the saw blade.
holder-rod assembly
Always secure the rip fence firmly, or dangerous
•
kickbacks may occur.
Always use "work helpers" such as push sticks
•
and push blocks when cutting small or narrow
workpieces, or when the ado head is hidden from
view while cutting.
Work helpers
Push sticks, push blocks or auxiliary fence are types of
"work helpers". Use them to make safe, sure cuts
without the need for the operator to contact the blade
with any part of the body.
Push block
55mm
1
(optional
1. Face/edge parallel
2. Handle
3. Wood screw
4. Glue together
005566
Use a 15 mm piece of plywood.
Handle should be in center of plywood piece. Fasten
with glue and wood screws as shown. Small piece 10
mm x 9 mm x 30 mm of wood must always be glued to
plywood to keep the blade from dulling if the operator
cuts into push block by mistake.
(Never use nails in push block.)
Auxiliary fence
Fig.46
Fig.47
Make auxiliary fence from 10 mm and 15 mm plywood
pieces.
Remove the rip fence, clamping screw (A), flat washer
and square nut from the rip fence holder and then
attach and secure the auxiliary fence to the rip fence
holder by using a bolt M6 longer than M6x50, washers
and nut.
Ripping
CAUTION:
When cutting long or large workpieces, always
•
provide adequate support behind the table. DO
NOT allow a long board to move or shift on the
table. This will cause the blade to bind and increase
the possibility of kickback and personal injury. The
support should be at the same height as the table.
1. Adjust the depth of cut a bit higher than the
thickness of the workpiece. To make this
adjustment, loosen two levers and lower or raise
the top table.
16
2
130mm
200mm
80mm
10mm
10mm
30mm 3
30mm
50mm
100mm
4
9mm