Noise/Vibration Information; Mounting And Operation - Bosch GHP 5-14 Originalbetriebsanleitung

OBJ_BUCH-1762-002.book Page 15 Tuesday, November 22, 2016 10:02 AM

Noise/Vibration Information

Sound emission values determined according to EN 60335-2-79.
Typically the A-weighted noise levels of the product are:
Sound pressure level
Sound power level
Uncertainty K
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K determined according to
h
EN 60335-2-79:
Vibration emission value a
h
Uncertainty K

Mounting and Operation

Action
Delivery Scope
Handle Assembly
Filling up detergent tank
Connecting to the water supply
Cleaning the Filter
Connecting high pressure water supply
hose/nozzle
Adjust water pressure
Adjust water jet
Switching On and Off
Clean nozzle
Starting
For Your Safety
Warning! Switch off, remove plug from mains be-
fore adjusting, cleaning or if cable is cut, damaged
or entangled.
Your pressure washer requires an earth connection. The op-
erating voltage is 230 V AC, 50 Hz (for non-EU countries
220 V, 240 V as applicable). Only use approved extension ca-
bles. Contact your Bosch Service Centre for details.
If you want to use an extension cable when operating your
high pressure washer, only the following cable dimensions
should be used:
2
- 2.5 mm – max length 20 m
2
- 4.0 mm – max length 50 m
Note: If an extension cable is used it must be earthed and con-
nected through the plug to the earth cable of your supply net-
work in accordance with prescribed safety regulations.
If in doubt contact a qualified electrician or the nearest Bosch
Service Centre.
WARNING! Inadequate extension cables can be
dangerous. Extension cable, plug and socket must
be of watertight construction and intended for
outdoor use.
Cable connections should be kept dry and off the ground.
Bosch Power Tools
For increased electrical safety use a Residual Current Device
(RCD) with a tripping current of not more than 30 mA. Always
check your RCD every time you use it.
Figure Page
If the supply cable on the product is damaged, it must only be
1 232
replaced by a Bosch Service Centre.
2 233
Products sold in GB only: Your product is fitted with an
3 233
BS 1363/A approved electric plug with internal fuse (ASTA
4 234
approved to BS 1362).
5 234
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should
6 235
have the same fuse rating as the original plug.
7 235
The severed plug must be disposed of to avoid a possible
8 236
shock hazard and should never be inserted into a mains sock-
9 236
et elsewhere.
10 237
For products not sold in GB:
WARNING: For your safety, it is required that the plug at-
tached to the machine is connected with the extension cord.
The coupling of the extension cord must be protected against
splash water, be made of rubber or coated with rubber. The
extension cord must be used with a cable strain relief.
Drawing in water from open reservoirs
– Screw the suction hose with filter (special suction kit part
no. F 016 800 335) to the water connection.
– Switch on the appliance in low pressure mode.
– Let the appliance run for appx. 10 seconds, then switch
off. Repeat the procedure a couple of times until water ex-
iting is smooth and bubble free.
To prevent damage to the appliance, do not allow it to operate
dry.
Operation
Starting
Attach water supply hose (not supplied) to the mains water
supply and machine.
Connect the product to the mains supply ensuring that the
mains switch is in the off position.
Open water tap.
Press the safety lock to release the trigger . Fully press the
trigger until there is a constant flow of water to clear the air
from the machine and water supply hose. Release trigger .
English | 15
3 600 ... J 10 1.. J10 2..
dB(A) 84.5 82.5
dB(A) 92 90
dB =3 =3
2
m/s =4.91 =4.91
2
m/s =1.5 =1.5
1 609 92A 3ER | (22.11.16)