Work Examples - Bosch GRL Professional Originalbetriebsanleitung

OBJ_BUCH-757-011.book Page 27 Wednesday, February 1, 2017 8:34 AM
Reception lenses 7 for the remote control are located on three
sides of the measuring tool, among other locations above the
control panel on the front side.
Working with the Tripod (Accessory)
– The measuring tool is equipped with a 5/8" tripod mount
for horizontal operation on a tripod. Place the measuring
tool via the tripod mount 18 onto the 5/8" male thread of
the tripod and screw the locking screw of the tripod tight.
On a tripod 37 with a measuring scale on the elevator column,
the height difference can be adjusted directly.
Working with Wall Mount/Alignment Unit (Accessory)
(see figure B)
You can also mount the measuring tool to the wall mount with
alignment unit 39. For this, screw the 5/8" screw 42 of the
wall mount into the tripod mount 18 of the measuring tool.
Mounting to a wall: Mounting to a wall is recommended, e.g.,
for work above the elevation height of tripods or for work on
unstable surfaces and without tripod. For this, fasten the wall
mount 39, with the measuring tool mounted, as vertical as
possible to a wall.
For mounting to the wall, you can either fasten the wall mount
39 with fastening screw 40 to a lath (width maximal 8 mm) or
hang it up with two hooks.
Mounting on a tripod: The wall mount 39 can also be screwed
onto a tripod with the tripod mount on the back side. This
method of fastening is especially recommended for work
where the rotational plane is to be aligned with a reference
line.
With the alignment unit, the mounted measuring tool can be
moved vertically (when mounted to the wall) or horizontally
(when mounted to a tripod) within a range of approx. 16 cm.
For this, loosen screw 41 on the alignment unit, move the
measuring tool to the desired position, and retighten screw
41 again.
Working with the Ceiling Measurement Plate
(see figure B)
As an example, the ceiling measurement plate 44 can be used
for easy height adjustment of drop ceilings. Fasten the ceiling
measurement plate with the magnetic holder, e.g., to a beam.
The reflecting half of the ceiling measurement plate improves
the visibility of the laser beam in unfavourable conditions; the
laser beam can also be seen from the rear side through the
transparent half.
Working with the Laser Target Plate (Accessory)
(see figure C)
With the laser target plate 43, the laser mark can be projected
on the ground/floor or against a wall. With the magnetic hold-
er, the laser target plate can also be fastened to ceiling con-
structions.
With the zero field and the scale, the offset or drop to the re-
quired height can be measured and projected at another loca-
tion. This eliminates the necessity of precisely adjusting the
measuring tool to the height to be projected.
Bosch Power Tools
The laser target plate 43 has a reflecting coating which im-
proves the visibility of the laser beam from a larger distance or
in case of strong sun rays. The luminosity can be recognized
only if you look to the laser target plate in parallel to the laser
beam.
Working with the Measuring Rod (Accessory)
(see figure J)
For checking irregularities or projecting gradients, it is recom-
mended to use the measuring rod 36 together with the laser
receiver.
A relative millimetre scale (±50 cm) is marked on the top of
the measuring rod 36. Its zero height can be preset at the bot-
tom of the elevator column. This allows for direct reading of
deviations from the specified height.

Work Examples

Projecting/Checking Heights (see figure C)
– Position the measuring tool in the horizontal position onto
a firm support or mount it onto a tripod 37 (accessory).
– Working with tripod: Align the laser beam to the requested
height. Project or check the height at the target location.
Working without tripod: Determine the height difference
between the laser beam and the height at the reference
point with the laser target plate 43. Project or check the
measured height difference at the target location.
Parallel Alignment of a Plumb Beam/Projecting Right An-
gles (see figure D)
When right angles are to be projected or when partitions are
to be aligned, the plumb beam 9 must be aligned parallel,
meaning at the same distance to a reference line (e.g. a wall).
– For this, set up the measuring tool in the vertical position
and position it in such a manner that the plumb beam runs
approximately parallel to the reference line.
– For exact positioning, measure the clearance between
plumb beam and reference line directly on the measuring
tool with help of the laser target plate 43. Measure the
clearance between plumb beam and reference line again
as far away as possible from the measuring tool. Align the
plumb beam in such a manner that it has the same clear-
ance to the reference line as when measured directly at the
measuring tool.
The right angle to the plumb beam 9 is indicated by the varia-
ble laser beam 6.
1 609 92A 273 | (1.2.17)
English | 27