GEV cab 087316 Bedienungsanleitung Seite 4

1- and 2-family house CAB doorphone set
Operating elements
Connection elements
Indoor unit (Fig. A)
Indoor unit (Fig. C)
1 Loudspeaker
1 External power supply connection (-)
2 Microphone
2 External power supply connection (+)
3 Open door button 3 Electromagnetic door opener
4 Coiled cable
connection
4 Electromagnetic door opener
Outdoor unit (Fig. B)
connection
1 Microphone 5 To outdoor unit <> 2
2 Loudspeaker 6 To outdoor unit <> 1
3 Ringer switch/nameplate 7 Supply voltage socket
4 Cover
Outdoor unit (Fig. D)
Power pack (Fig. E)
1 To indoor unit <> 6
1
1 Plug 2 To indoor unit <> 5
1 To indoor unit <> 6
2
2 To indoor unit <> 5
Please read these instructions carefully and keep for future
reference. By purchasing this item, you have chosen a high-
quality GEV product. Please read these operating instructions
carefully to ensure correct operation. Keep these instructions
in a safe place so that you can refer back to them if necessary.
Safety instructions
Under no circumstances does the warranty cover
damage resulting from failure to observe these
instructions. Nor do we accept liability for any indirect
damage. Similarly, we can accept no liability for any
material damage or bodily injury caused by mishandling or failure
to observe the safety instructions. In these cases, no warranty
or guarantee claim may be made. In addition, for safety and
compliance reasons, you are not authorised to dismantle or alter
the device in any way.
Door opener
An electromagnetic door opener can be connected via the indoor
unit to the CAB doorphone set. The CAB doorphone set supplies
this with voltage. Please observe the technical data.
Installation
If in any doubt, rather than mounting, connecting or installing the
equipment yourself, contact a qualifi ed technician.
The outdoor unit is designed for surface mounting. When deciding
where to install the outdoor unit, ensure, wherever possible, that
you choose a position that is well shielded from the elements,
particularly rain. Remove the cover (B4) and undo the screws as
shown in Fig. F. Carefully remove the cover (B3) to write on the
nameplate. Connect up the doorphone set as shown in Fig. I.
Install the outdoor unit as shown in Fig. G and fi t the seal so that
the open ends face downwards.
Install the indoor unit as shown in Fig. H. Screw in the screws,
leaving the screw heads sticking out of the wall by about 5 mm.
Carefully hang the indoor unit on the screws using the unit's
fastening eyes and push it downwards.
Activation/Operation
Connect the power pack plug (E1) to the socket (C7).
Alternatively, you can use an external power supply (not supplied)
and connect it to terminals 1 and 2 (Fig. C).
Do not exceed the maximum permissible DC voltage of 12 V. Once
the nameplate (B3) on the outdoor unit lights up, the system is
ready for use. When the ringer switch (B3) is pressed, the indoor
unit will ring. You can now simply lift the receiver and start talking.
Press the open door button (A3) to activate the (optional) door
opener. Simply hang up the receiver to stop the connection.
EC compliance information
Using the device near electromagnetic high frequency fi elds
such as radio systems, microwaves or mobile phones, or high
electrostatic discharge, can interfere with device operation.
Should you encounter problems, switch the power supply off and
on again to restore operation.
Recycling instructions
This device may not be disposed of with unsorted
household waste. Owners of old devices are required by
law to dispose of this device correctly. Contact your town
council for further information.
4
Troubleshooting - practical advice
Fault Cause
No bell tone/signal • Is the power supply connected?
• Is the power supply faulty?
• Is the cable connecting the indoor and
outdoor units incorrectly connected/
faulty?
• Is the device faulty?
Technical information
Operating voltage
Outdoor unit temperature range
Indoor unit temperature range
Power consumption
Recommended cable
Distance from indoor to outdoor unit
Operating voltage for door opener
Protection type/Outdoor unit
Protection type/Indoor unit
Indoor unit dimensions
1-/2- family house outdoor unit dimensions
Technical information power pack
Input voltage
Output voltage
Rated current
Technical and design features may be subject to change without notice.
Gutkes GmbH
Rehkamp 13 Fax: +49 (0)511/95 85 805
30853 Langenhagen www.gev.de
Germany service@gev.de
Solution
• Connect the power pack
• Check the power pack
• Check the cable
• Check the device
12 V
-10 °C to +40 °C
0 °C to +35 °C
max. 3.5 W
J-Y(ST)Y 4x2x0.8
max. 100 m
12 V / max. 1 A
IP44
IP20
approx. W 72 x H 236 x D 75 mm
approx. W 110 x H 157 x D 36 mm (excluding waterproof housing)
100 V - 240 V ~, 50/60 Hz
12 V
max. 1 A
5