ThermoTec MICRO 500 Bedienungsanleitung Seite 9

USER MANUAL
MICRO 500
General Information
1
Guarantee conditions
2
Manual on assembly of pedestals
3
Manual on disassembly of pedestals
4
Manual for FlexiSmart controller
5
General Information
1
Please read the user manual of your MICRO 500 and the information
listed here carefully. Store these instructions in a safe place and pass
them on to the following owner, if necessary. This demo device is only
for demonstration purpose. The warming of rooms with the MICRO 500
is prohibited.
1. Purpose & use
The MICRO 500 is not an electrical heater, but a demonstration model,
to show the functionality of the heater manufacturer in order to pro-
mote the product.
The MICRO 500 must be served only by instructed and skilled mer-
chants to promote the features of the device. The MICRO 500 must not
be used by end-users, especially not by persons with impairment of
motor or psychic functions.
2. Safety instructions
The MICRO 500 must be served only by instructed persons. During
operation and cooling phase the device has to be supervised, so that
no other can touch the device.
The MICRO 500 is only suitable for operation inside enclosed rooms.
Damaged devices (e.g. damaged connecting cables) must not operated.
The MICRO 500 must not be placed directly below a wall socket. The
MICRO 500 is not intended to be used by persons (including children)
with limited perceptual abilities or by people with lack of experience
and / or lack of knowledge of using it. Unless they are supervised by a
person responsible for their safety or have received instructions from
this person on how to use the heater. Children should be supervised to
ensure that they do not play with the heater.
Futher safety instructions:
• The device is not suitable for heating and must not be used in conti-
nuous operation.
• The device is tested according to the applicable IP protection class
when properly installed (International Protection Code – in this case
IP 40: not protected against spray water).
• Components can become very hot – danger of burning
• Do not touch the device during operations – danger of burning
• Do not hand inside the device during operations and cooling phase
– danger of burning
• Do not touch the exposed chamotte stone.
• Only carry completely cooled down in the carrying case.
• Only put the device on heat-resistant surfaces.
• Do not put highly inflammable objects next to the device (minimum
distance 1m).
• Do not immerse electrical parts of the device into water or other flu-
ids during cleaning or operations. Never put the device into running
water.
• Do not place heavy objects on the device.
• The device is not a toy.
• Do not put any objects with open flame next to, on to or next to the
device, e.g. candles (minimum distance 1m).
• Do not put any objects with fluids on the device, e.g. vases (minimum
distance 1m).
• 4 minutes after the warming phase, turn the device off. Otherwise
the device becomes very hot – danger of burning.
• Put the MICRO 500 in the appropraite case, after it has completely
cooled down.(cooling phase approx. 40 minutes).
• Always first turn device off, and then pull the power plug.
• The thermosensitive sticker only provides an approximate value and
does not show a accurate temperature.
• Always run the device upright with the original delivered pedestals.
The device is not allowed to be operated horizontal!
3. Electrical connection
Your MICRO 500 is not suitable for fixed connection to wall sockets or
operation from wall connection sockets. The operation is only allowed
with classic sockets. The device is not allowed to be operated on
multiple sockets.
If the main connection cable of the MICRO 500 is damaged, it needs to
be replaced by us or a suitably qualified electrician in order to prevent
danger and additional damage.
The MICRO 500 may only be operated with the thermostat mounted
directly on the device.
4. Insttallation and transport
The MICRO 500 must not be mounted on wall or ceiling. The device
must only be operated with the provided pedestals. Please ensure that
the heater can radiate into the room as freely as possible. In order
to transport the MICRO 500, the device has to be completely cooled
down. The MICRO 500 is cooled down after approx. 40 minutes. Do not
transport the device if it is not completely cooled down, also not in the
provided carrying case.
You can find our detailed installation information on page 9.
5. MICRO 500 operation
The nominal power is 500 W on 230 V. The power consumption varies
between 480 W and 530 W. The device must not be used in continuous
operation and has to be unplugged from power supply after 4 minutes
of heating.
If the device is as indicated not disconnected from the power supply af-
ter 4 minutes of heating, it will heat to over 130 ° C. Danger of burning!
Do not touch the the exposed chamotte stone and the device during
operation (incl. cooling phase). Avoid direct skin contact.
The MICRO 500 is managed with the internally mounted intern
thermostat. It is possible that a slight odour can develop during initial
commissioning, since some materials still have to emit fumes. This
does not pose any threat, and it will stop after a period of time. Please
ventilate the rooms well if necessary. In rare cases, noise can occur in
the form of cracking, which is caused by heat-induced material move-
ments, which are harmless.
6. Overheating protection
Do not cover the air vents. Do not cover the MICRO 500 (e.g. with
towels) during operation. Fire hazard! Any resulting defects on a tem-
perature switch and the resulting costs for the repair shall be borne
exclusively by the party causing the damage.
7. Malfunctions
If the MICRO 500 does not emit any heat, please check that the ther-
mostat is pre-set to the desired temperature. In addition, it is essential
to check that the local power distribution is switched on or that the
fuse is in working order. If you encounter such malfunctions, please
contact your qualified electrical workshop. In the event of a complaint
being addressed to us, the serial number of the device is required for
order processing. You will find this information on the rating plate. The
device must not be used, if the mains cable or the plug is damaged or
if the device has any malfunctions. A damaged mains cable must be
only replaced by a qualified electrical workshop. Never try to repair the
device on your own. Risk of electrical shock.
8. Cleaning of device
Turn the MICRO 500 off before each cleaning sequence and allow it to
be cooled down completely. Switch the mains cable before each clea-
ning sequence. Only wipe the MICRO 500 off with a soft, damp cloth
and do not use any chemical detergents or abrasive. A correspondingly
designed cleaning brush can be used for the cleaning of the slats (not
included). We offer you an appropriate product in our online shop for
purchase in the accessories section.
Do not immerse electrical parts of the device into water or other fluids
during cleaning or operations. Never put the device into running water.
Disposal of electrical equipment
The equipment marked with this symbol, and thus also the electric
radiators, must not be disposed of with household waste. Under our
production responsibility as a manufacturer, we are committed to
environmentally friendly treatment and recovery of waste equipment.
The placing on the market as well as the collection and recovery
of electrical equipment in the European Economic Area (EEA) are
essentially governed by Directive 2012/19/EU on waste electrical and
electronic equipment and its national transpositions.
The radiator can be taken to a recycling centre for electrical and
electronic equipment. For further information on the collection and
disposal of used equipment, please contact your dealer or local autho-
rities.If necessary, provide the following WEEE number: DE 46197075.
Disposal outside Germany: Dispose of the equipment professionally
and properly in accordance with the local laws and regulations. Proper
disposal and recycling of raw materials contribute to the protection of
the environment. By using raw materials in a conscious and cost-effec-
tive way, you care about yourself and your loved ones.
Tips for handling used equipment: Disconnect the mains plug! Cut off
the power cord and discard it with the plug! Do not let children play
with worn equipment!
Disposal of equipment packaging
The packaging is used to protect the equipment from damage during
transport. All packaging materials should be disposed of in accordance
with the applicable legal regulations. For more information, contact
the local authorities. The packaging material used is environmentally
friendly and suitable for reuse or recycling. The corrugated board used
reaches a recycling rate of almost 100%. The transparent protective
films are made of completely harmless and food-safe polyethylene
9