Herunterladen Inhalt Inhalt Diese Seite drucken

Gas Supply Connection - Whirlpool B 10TC/CS BNV F Installationanleitung Und Betriebsanleitung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

Gas supply connection

Gas supply connection
Gas supply connection
Gas supply connection
Gas supply connection
• Check that the appliance is set for the type of gas available
and then connect it to the mains gas piping or the gas
cylinder in compliance with current regulations and
standards.
• This appliance is designed and set to work with the gas
indicated on the label situated on the actual hob. If the gas
supply is other than the type for which the appliance has
been set, proceed with replacing the corresponding nozzles
(provided), following instructions given in the paragraph
"Adaptation to different types of gas".
• For trouble-free operation, suitable use of energy and longer
life of the appliance, make sure that the supply pressure
complies with the values indicated in the table 1 "burners
and nozzles specifications, otherwise install a special
pressure regulator on the supply pipe in compliance with
current standards and regulations.
• Connect in such a way that the appliance is subjected to
no strain whatsoever.
Either a rigid metal pipe with fittings in compliance with the
standards in force must be used for connecting to the nipple
union (threaded ½"G male fitting) situated at the rear of the
appliance to the right (Fig.7), or flexible steel pipe in
compliance with the standards in force, which must not
exceed 2000 mm in length. Should it be necessary to turn
the fitting, the gasket (supplied with the appliance) must be
replaced. Upon completion of installation, check the gas
circuit, the internal connections and the taps for leaks using
a soapy solution (never a flame). Also check that the
connecting pipe cannot come into contact with moving parts
which could damage or crush it. Make sure that the natural
gas pipe is adequate for a sufficient supply to the appliance
when all the burners are lit
Important:
Important:
Important:
Important:
Important: A pressure regulator, in compliance with the
standards in force, must be inserted when connecting to a
liquid gas supply (in a cylinder).
Adaptation to a different type of gas
Adaptation to a different type of gas
Adaptation to a different type of gas
Adaptation to a different type of gas
Adaptation to a different type of gas
If the hob is to be converted for use with a type of gas other
than that for which it was set in the factory (indicated on the
label to be found on the hob), the burner nozzles should be
replaced as follows:
• Remove the pan supports and the burners.
• Unscrew the nozzles "A A A A A " (Fig.7) using a 7 mm socket
wrench and replace them with the ones which have a
diameter suitable for the type of gas to be used, according
to the table 1 "burners and nozzles specifications).
• On completing the operation, replace the old rating label
with the one showing the new type of gas; the sticker is
available from our Service Centres.
Adjusting the low flame
Adjusting the low flame
Adjusting the low flame
Adjusting the low flame
Adjusting the low flame
· Put the tap to the low flame position;
· Remove the tap knob and turn the adjusting screw, situated
inside of the tap stem (Fig.8), using a screwdriver
(loosening the screw increases the height of the flame,
tightening decreases it).
note: the adjusting screw must be fully screwed down for
note:
note:
note:
note:
liquid gas.
· Having obtained the low flame setting required and with
the burner lit, abruptly change the position of the knob
several times from minimum to maximum and vice versa
and check that the flame does not go
Gas supply connection
Gas supply connection
Gas supply connection
Gas supply connection
Gas supply connection
Replacing the nozzles on separate "double flame "
Replacing the nozzles on separate "double flame "
Replacing the nozzles on separate "double flame "
Replacing the nozzles on separate "double flame "
Replacing the nozzles on separate "double flame "
burners:
burners:
burners:
burners:
burners:
• remove the grids and slide the burners from their housings.
• unscrew the burers with a 7 mm wrench spanner. The
• replace all the components by repeating the steps in
Regulation of Air Supply to the Burner
Regulation of Air Supply to the Burner
Regulation of Air Supply to the Burner
Regulation of Air Supply to the Burner
Regulation of Air Supply to the Burner
The burners do not need a primary air regulator.
Minimum Regulation
Minimum Regulation
Minimum Regulation
Minimum Regulation
Minimum Regulation
• Turn the gas valve to minimum.
• Remove the tap knob and turn the adjusting screw, situated
inside of the tap stem (Fig.9), using a screwdriver (loosening
the screw increases the height of the flame, tightening
decreases it).
N.B.:
N.B.: In the case of liquid gas, the regulation screw must
N.B.:
N.B.:
N.B.:
be fully screwed in (clockwise).
• Make sure that, when the knob is turned rapidly high to
low, the flame does not go out.
• In the event of a malfunction on appliances with the security
device (thermocouple) when the gas supply is set at
minimum, increase the minimum supply levels using the
regulator screw.
Once the adjustment has been made, apply sealing wax, or
a suitable substitute, to the old seals on the by-pass.
16
16
16
16
16
fig.7
fig.9
The burner consists of 2 separate parts (Fig. C and fig.
D);
internal burner has a nozzle, the external burner has two
(of the same size). Replace the nozzle with models suited
to the new type of gas (see table 1).
reverse order.
Fig. C
fig.8
Fig. D

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis