Lezyne LITE DRIVE 1200+ Kurzanleitung

QUICK START - LITE DRIVE 1200+ / MICRO DRIVE PRO 1000+/ MICRO DRIVE 800+ / FUSION DRIVE PRO 600+ / FUSION DRIVE 500+ - ENGLISH
READ ENTIRE MANUAL BEFORE OPERATION to ensure proper use and care of your new Lezyne LED light. Traffic laws mandating
lighting vary from country to country. Inform yourself about lighting laws and regulations in the country Of use. Lezyne LED lights
do not conform to the German road traffic regulation
LITE DRIVE 1200+ MICRO DRIVE PRO 1000+
Warnings
DO NOT LOOK DIRECTLY INTO LIGHT BEAM or shine into eyes of another.
Lezyne LED Lights have a water resistance rating of IPX7 under IEC standard
the device is not recommended. If moisture does enter the casing, air out until completely dry.
DO NOT ATTEMPT TO REMOVE ELECTRONICS. Doing so will void warranty.
Lezyne USA, Inc. does not accept any liability for injuries or other damages resulting
of this product in any circumstances.
Warranty
In U.S. and U.K., Lezyne LED Lights carry a two (2) year warranty from the original purchase date to the original owner (proof Of
purchase required). Lezyne Batteries carry a six (6) month warranty from the original purchase date. Lezyne warranties cover any
manufacturing defects in materials or workmanship.
installation, attempting to access or modify electronics, damage or failure due to accident, misuse, abuse and/or neglect.
For all warranty issues worldwide, please contact the retailer that sold the product.
For any warranty questions contact: warranty@lezyne.com
Mounting
Operation
1. On/Off: hold button two (2) seconds.
2. Mode cycle: click button
RACE MODE: With the light OFF, hold button for five (5) seconds, until light flashes.
The light is now in RaceMode where only Overdrive and Economy outputs are selectable. The light will remain in Overdrive Race Mode
even when switched OFF. Repeat the step above to return to the normal mode set.
MODE MEMORY: The light remains in the output setting it is switched OFF in.
THERMAL PROTECTION: If the operating temperature Of the light is too high, the light automatically lowers the lumen output.
Run Times and Modes
LITE DRIVE 1200+
ECONOMY BLAST OVER ORIuc
150
600 700
LUMENS LUMENS LUMENS LUMENS LUMENS LUMENS
20:00 9:30 4:00 2:00 40:00 60:oo
h : min h : min h: min h : min h : min h
RACE MODE
MICRO DRIVE PRO 1000+
ECONOMY BLAST OVER
125 600 M ooo 700
LUMENS LUMENS LUMENS LUMENS LUMENS LUMENS
11:00 6:00 3:15 40:oo 60:oo
h : min h : min h: min h : min h: min h: min
RACE MODE
MICRO DRIVE 800+
*LASH
i' 8100
400 s800 700 20
LUMENS LUMENS LUMENS LUMENS LUMENS LUMENS
10:00 3:00 2:00 30:oo 35:oo 10:00
h: min h: min h: min h : min h: min h: min
• Please read all instructions before use
• Lea todas las instrucciones antes de usar
• Veuillez lire les instructions avant utilisation
• Bitte lesen Sie wor dem ersten Gebrauch alle Anweisungen durch
Lezyne USA, 645 Tank Farm Rd., Unit F, San Luis Obispo, California 93401
StVZO.
MICRO DRIVE 800+ FUSION DRIVE PRO 600+
60529. Submerging
from the use
Issues not covered by warranty include normal wear & tear, improper
FUSION DRIVE PRO 600+
FEMTO ZNDL'RO rsl_nsr
20 300 600
100 100
LUMENS LUMENS LUMENS LuMENS
14:00 10:00 5:00 2:00
min h : min h : min h: min h: min
FUSION DRIVE 500+
FEN ro PULSE ßLAsr
20 100 100 250 500
LUMENS LUMENS LUMENS LUMENS
14:00 9:00 3:30 1:45
h : min h : min h: min h: min
100
Battery Indicator
An LED, located in the button,
display battery status.
FUSION DRIVE 500+
Chargingfor FUSION DRIVE 500+I FUSION DRIVE PRO 600+IMICRO DRIVE 800+I MICRO D RIVE P RO 1000+
Before using your Lezyne LED Light for the first time, fully charge battery.
To charge your light:
1. Switch light OFF
2. Remove USB-C protective
3. Insert USB-Cplug into powered USB-Cport
4. Once charging, button
If button does not flash when plugged in, selected USB-Cport may not be powered—try another USB-Cport.
Light will be charged after 3—5hours or when button is solid green.
5. Remove light from charger and reinstall USB protective cover—ensure USB protective cover is fully installed for water
resistance.
Charging
Flashes green Illuminates green
Chargingfor LITE DRIVE 1 200+
Before using your Lezyne LED Light for the first time, fully charge the battery.
TOcharge your light:
Switch light OFF
1.
2. Remove USB-C protective
3. Connect USB-Ccable and light to powered USB-Cport
4. Once charging, button will flash green; if USB-Cport is capable, light will use High Efficiency (HE) charging and button will flash
blue.
If button does not flash when plugged in, selected USB-Cport may not be powered—try another USB-Cport.
Light will be charged after 5—6hours (3—5with HEcharging) or when button illuminates solid green or blue.
5. Remove light from charger and reinstall
resistance.
Charging
Flashes green Illuminates green
FLASH pul_sc
20
600 100
LUMENS LUMENS L UMENS
36:oo 36:oo 12:00
h : min h: min
pucsE
500 20 100
LUMENS LUMENS LUMENS
30:oo 35:oo 12:00
h : min h: min h : min
displays current battery status while light is ON. When light is OFF, click button
100% 10%
(5
Illuminates green Illuminates yellow Illuminates
cover
will flash green
Fully Charged
4
USB-C Cable Not Included
cover
USB-C protective cover—ensure USB-C protective
Fully Charged
USB-C Cable Not Included
74354-YII-LED-LITEDRIVE-MICRODRIVEPRO-MICRODRIVE-FUSIONDRIVEPRO-FUSIONDRIVE-PLUS-QUICK-RIAI
once to momentarily
5%
red Flashes red
cover is fully installed for water
Charging Fully Charged
Flashes blue Illuminates blue
High Efficiency (HE) charging
For more info go to: www.lezvne.com/support.php