Conrad My Wall HP65L Kurzanleitung

NOTE: No-load running prohibited!
!
Before power connection, be sure that bracket and the TV installed correctly.
Keep the children away from power.
HP 65 L
2x AAA battery (not included)
Upward Movement
Press and hold the button to lift the mount.
(Tips: Clear up all obstacles
within the range of motion.)
Press the button and the mount will
automatically get to the position saved
in the corresponding button mem1. Press
any button to stop motion.
Press the button for 3 seconds until you hear a
beep, indicating that the current position
has been saved to memory.
Reset Mode
Disconnect the power supply cord. Wait for 10 seconds and reconnect. Long press the OK button for 5 seconds until you hear a
beep. The mount starts to move upward to the highest position and the control box emits a double beeps.
Connect the Mount to a New Device
Short press the mem2 button five times, you will hear two beeps at the fifth press, which indicates the mount is disconnecting from the
current paired device. Then follow the Guidebook of Tuya App Installation and Operation to connect the mount to a new device.
NOTE: lf the device is failed to search the rnount when connecting, follow the above steps or restart the device to re-search the rnount.
Coding of Remote Controller and Control Box
Step 1: When the mount is powered on, press the small button on the control box with a thin tool as shown.
The unit emits a beep, indicating that the control box is on standby for program coding.
Step 2: Press the SET button on the remote control, and the control box repeatedly beeps for approximate 10 seconds
indicating that the remote control is being programmed. The process will be finished automatically until you can't hear
a beep any longer.
NOTE: Clear up the historical data when replacing a new remote control to pair. Press the small button on the control
box with hearing a beep, and hold for 10 seconds to confirm the data-cleaning process is completed until you hear a
long beep.
TROUBLESHOOTING
If a problem arises, please try the troubleshooting guidelines below. If the problem is not listed, please contact your
local distributor for additional technical assistance.
The motorized TV mount does not respond to remote control.
Possible reasons caused by TV mount or remote control.
TV MOUNT
1.)The system may be overheating. Check if the unit beeps four times after pressing the button. If so, allow the unit to cool down and return to
room temperature (about 12 minutes).
2.)The AC/DC end of the power cord may be unplugged/disconnect from the outlet/mount. Check the connection to the outlet/mount to
ensure the unit has power.
REMOTE CONTROL
1.)The remote control operating distance may be too far and not in range of the mount. Acceptable range should be less than 10m (30 feet).
2.)The batteries in the remote control may be low or dead. Replace the batteries.
3.)The remote control may be broken. Check to see if the indicator LED found on the remote lights when a button is pressed. If not, contact your place of
purchase for a replacement.
The TV mount stops moving during operation and emits a long beep.
1.)Check to see if a foreign object is impeding the mount from moving. If so, remove the object.
2.)The weight of TV may exceed the maximum weight limitation of the mounting system.
3.)The motor wire may be broken. Reset the system. If the problem still exists, contact your place of purchase for replacement.
The TV mount is making an abnormal noise or sound.
1.)Check all power connections and reset the system. If the unit continues to make an abnormal noise, please contact your place of
purchase for a replacement.
Hereby, Transmedia Kabelverbindungen GmbH declares that the TV Wall Mount HP 65 L is in compliance
with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:
https://www.transmedia-germany.com/download
Recall Memory
Memory Setting 1
OK Button
Short press the button and the mount will automatically retract
to the highest position. Press any button to stop motion.
Downward Movement
Press and hold the button to lower the mount.
(Tips: Clear up all obstacles within the range of motion.)
Recall Memory
Press the button and the mount will automatically
get to the position saved in the corresponding
button mem2. Press any button to stop motion.
Memory Setting 2
Press the button for 3 seconds until
you hear a beep, indicating that the
current position has been saved to
memory.