Description Of Symbols; Specification - Silverline 656578 Bedienungsanleitung

GB
Introduction
Thank you for purchasing this Silverline tool. This manual contains information necessary
for safe and effective operation of this product. This product has unique features and, even if
you are familiar with similar products, it is necessary to read this manual carefully to ensure
you fully understand the instructions. Ensure all users of the tool read and fully understand
this manual.

Description of Symbols

The rating plate on your tool may show symbols. These represent important information about the
product or instructions on its use.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
Wear head protection.
Wear hand protection.
Read instruction manual.
DO NOT use with compressed gas cylinders!
Conforms to relevant legislation and safety standards
Environmental Protection
Air tools should not be disposed of with household waste. They contain traces of
oil and other lubricants. Please recycle where facilities exist. Check with your local
authority or retailer for recycling advice
4
Original Instructions

Specification

Maximum operating pressure:........................................6.3bar (90psi)
Air consumption: .............................................................140L/min (5cfm)
Air Inlet:.............................................. .. ..........................¼" BSP, supplied with two
Minimum hose diameter:...................... ..................9.5mm (3/8")
Square drive:............................................ .......½"
Directions:............................................... .......forward & reverse
No load speed:..................................... ...........................150min-1
Max. torque:......................................... ...........................61Nm
Weight................................................... ..........................1.25kg
Noise and vibration information:
Level of sound pressure according to Machinery directive 2006/42/EC:
Sound Pressure .................................................................L
Sound Power .....................................................................L
Uncertainty .......................................................................K = 3dB
The sound intensity level for the operator may exceed 85dB(A)
and sound protection measures are necessary.
Vibration total values (triax vector sum) according to Machinery directive 2006/42/EC:
Vibration emission value ..................................................ah = 3.27m/s
Uncertainty .......................................................................K = 1.5m/s
As part of our ongoing product development, specifications of
Silverline products may alter without notice.
Noise and Vibration
Sound and vibration levels in the specification are determined according to ISO 28927-3. The
figures given can be used to compare similar tools tested to this standard. These figures may be
used to assess exposure to noise and vibration levels.
The figures represent normal use for the tool in normal working condition. A poorly maintained,
incorrectly assembled or misused tool may produce increased levels of noise and vibration. The
total working period that you can operate this tool must factor in periods where the tool is idle or
switched off. Allow frequent rest breaks when operating this tool.
It is in the interest of users to maximise their safety using the correct safety equipment, like ear
defenders that protect against loud or repetitive noise, and anti-vibration gloves that minimise
vibration. Do not operate the tool with your hands below a normal comfortable temperature, as
vibration will have a greater effect.
Sound
The noise directive was introduced to protect against the risk to health and safety arising or likely to
arise from exposure to noise and risk of hearing. The Directive can be used to define noise exposure
and the physical parameters, such as peak sound pressure and daily and weekly exposure level.
Particular attention should be taken to exposure level and duration.
For more information on the Noise Directives 2003/10/EC and 2000/14/EC, please visit The
European Agency for Safety and Health at work - www.osha.europa.eu.
Vibration
The European Physical Agents (Vibration) Directive 2002/44/EC was introduced to control the
exposure of vibration at work. The Directive enables users of tools to make informed decisions on
the amount of time spent working. Those who regularly operate high vibration equipment over a
sustained period of time are at a higher risk of health problems. ISO 28927-3 measures vibration
in three directions which is known as tri-axial or vector sum measurement. When operating high
vibration equipment, ensure not to exceed exposure levels. For more details on The Vibration
Directive 2002/44/EC please visit The European Agency for Safety and Health at work -www.osha.
europa.eu
male airline quick connectors
(EN-6 'UK' and EQ-4 'European' types)
= 91dB(A)
PA
= 102dB(A)
WA
2
2