Bort BHR-2300-Pro Bedienungsanleitung Seite 10

• Do not disconnect the plug by pulling on the electrical
cable .
• If you are too far from the object you wish to clean, do
not move the cleaner nearer by pulling on the high pres-
sure hose; use the handle provided .
• Do not obstruct the ventilation grilles during operation .
• The cross-section of any extension cables used must be
proportional to their length, i .e . the longer the extension
cable, the greater the cross-section; cables with a protec-
tion level of "IPX5" must be used .
• Position the high pressure cleaner AS NEAR POSSIBLE to
the water supply .
• Use the high pressure cleaner only with accessories and
replacement parts authorized by the manufacturer . The
use of original accessories and replacement parts will en-
sure safe, trouble-free operation .
• Avoid unintentional firing of the trigger . Do not carry
the lance / trigger assembly with your hand over the trig-
ger . Always use the trigger lock mechanism .
• Ensure that the safety lock on the trigger is used, when
you have stopped using the pressure washer to prevent
accidental operation .
• Do not use the cleaner with inflammable or toxic liquids,
or any products which are not compatible with the correct
operation of the high pressure cleaner .
• Do not direct the water jet towards the unit itself, electri-
cal parts or towards other electrical equipment .
• Do not allow children or incompetent persons to use
the high pressure cleaner .
• Do not touch the plug and/or socket with wet hands .
• Do not use the high pressure cleaner if the electrical ca-
ble is damaged .
• Do not use the high pressure cleaner if the high pressure
hose is damaged .
• Do not jam the trigger in the operating position .
• Check that the data plates are affixed to the high pres-
sure cleaner, if not, inform your dealer . Cleaners without
plates must NOT be used as they are unidentifiable and
potentially dangerous .
• Do not tamper with or alter the calibration of the safety
valve .
• Do not alter the original diameter of the spray head
nozzle .
• Do not leave the high pressure cleaner unattended .
• Do not move the high pressure cleaner by pulling on the
electrical cable .
• All electrical conductors MUST BE PROTECTED against
the water jet .
• The high pressure cleaner MUST ONLY BE CONNECTED
to a correctly earthed power supply .
• The high pressure may cause materials to bounce off
surfaces at speed; therefore protective clothing and safety
goggles MUST BE WORN .
• Before doing work on the cleaner, REMOVE the plug .
• Before pressing the trigger, GRIP the gun firmly to coun-
teract the recoil .
• Maintenance and/or repair of electrical components
MUST be carried out by qualified staff .
• DISCHARGE residual pressure before disconnecting the
high pressure cleaner hose .
• Before using the high pressure cleaner, CHECK every
time that the screws are fully tightened and that there are
no broken or worn parts .
• Only USE detergents which will not corrode the coating
materials of the high pressure hose/electrical cable
• ENSURE that all people or animals keep a minimum dis-
tance of 16 yd . (15m) away .
ASSEMBLY
• Connecting water hose to inlet first,and turn on the tap .
Make sure the machine is full of water . .Then turn on the
main switch .The most important thing is not forget to
press the in electronic control center to start the machine .
• The electronic control center has three pressure modes
for users to choose . There are soft, medium and strong
mode .The pressure depends upon which attachment is
best suited to the surface you are cleaning .
• If you want to increase the pressure level, press the +
button in the electronic control center .
• If you want to reduce the pressure level, press the - but-
ton in the electronic control center .
• When you increase the pressure level to make the
pressure indicator turn red, it means that the machine is
working at the maximum pressure . At this time, please do
not let the machine work continuously for more than 15
minutes under the maximum pressure .
PRE-OPERATION
Adjusting fan pattern
Water can be sprayed either with a narrow jet or fan-
shaped . The kit includes 4 nozzles with a non-adjustable
spray angle of 0o, 15o, 25o, 40o . Install the required nozzle
before starting work, depending on the task .
Nozzle cleaning instructions
A clogged or partially clogged nozzle can cause a signif-
icant reduction of water coming out of the nozzle and
cause the unit to pulsate while spraying . To clean out the
nozzle:
1 . Turn off and unplug unit .
2 . Turn off water supply . Relieve any pressure trapped in
the hose by squeezing trigger 2-3 times .
3 . Separate lance from gun .
4 . Rotate nozzle to the narrow stream setting . This opens
up the fan blades .
5 . Using included tip cleaner, or an unfolded paper clip,
insert wire into the nozzle hole and move back and forth
until debris is dislodged .
6 . Remove additional debris by back-flushing water
through the nozzle . To do this, place end of a garden hose
(with water running) to end of nozzle for 30-60 seconds .
EXPLOITATION
When spraying water against a surface, maximum impact
10