Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
3. Auto-run program mode
Press"MODE"button,select the auto-run program mode. There are three modes in the auto-run program
mode. You can select them by pressing the"SET UP" button.
1) Color dreaming program mode select
Press "SET UP" button until the four digital tube displays "
button to select the 24 color dreaming programs 1-24.
2) Color jumping program mode select
Press "SET UP" button until the four digital tube displays "
button to select the 24 color jumping programs 1-24.
3) Color dreaming/jumping speed select
Press"SET UP"button until the four digital tube displays "
to select the color dreaming/jumping speed 01-16, 01 is the slowest speed, 16 is the fastest speed.
4. Static color select mode
Press"MODE"button, select the static color select mode. There are three modes in the static color select
mode. You can select them by pressing the"SET UP" button.
1) LED tube select mode
Press"SET UP"button, select the LED tube select mode. At this time, the four digital tube displays
"
/
~
displayed means that you can select static color for all the LED tubes. When"
means that you can select static color for the corresponding single LED tube. For example:
represent the LED tube 1 and so on.
2) Static color select
Press "SET UP"button until the four digital tube displays "
select static color 0-7 under this mode.
0---black 1---red 2---green 3---blue 4--- yellow 5---purple 6---cyan 7---white
3) Flash speed select
Press "SETUP" button until the four digital tube displays "
button to select the static color flash speed 00-15, 00 is flash off, 01 is the slowest flash speed, 15 is the
fastest flash speed.
5. Other program select mode
1) Display off/on select mode
Press "SET UP" button, select display off/on mode. Press UP or DOWN to select the four digital tube display
on/off. When the digital tube displays "
digital tube displays "
operation.
2) Display normal/inversion select mode
Press"SETUP" button, select display normal/inversion mode. Press UP or DOWN to select the four digital
tube display normal/inversion. When the digital tube displays "
normally, when the digital tube displays "
3) Initialization select mode
Press "SETUP" button until the four digital tube displays "
button and DOWN button at the same time, you can initialize it at extra factory setting, running into the first
color jumping mode, and the four digital tube displays "
6. DMX mode
You can control the devices individually via your DMX-controller.
Note: The LED digital tube controller is under slave mode in any situation of the DMX mode (any DMX
address, any DMX channels mode) when it is combined to other LED digital tube controller but not
512DMX-controller.
1) DMX address select mode
The control Board allows you to assign the DMX address which is defined as the first channel of the LED
digital tube CONTROLLER.Press "MODE" button until the display is "
DOWN to set the DMX address. The four digital tube display will be flicker when there is no controller signal.
2) Channel set mode
In DMX-mode, you can select between 4 modes. Press "SETUP" button until the display shows
"
/
/
", then press "UP" or "DOWN" button to select the LED tube. When "
" means that the display will on in any situation, when the
" means that the display will be automatically off after 20 seconds if there is no
" means that the digital tube displays inversion.
/
", then press UP or DOWN to set the desired channels (5,7,32,480).
~
~
~
~
~
" means that the digital tube displays
" and the display is flicker. Now press UP
".
23/27
", then press "UP" or "DOWN"
", then press "UP" or "DOWN"
". Press "UP" or "DOWN" button
~
" is displayed
", then press "UP" or "DOWN" to
", then press "UP" or "DOWN"
~
", then press UP or
00065031.DOC, Version 1.0
" is
Werbung
Inhaltsverzeichnis
